#1: Cam and crankshaft locking tools - where from? Author: neilneil2000, Posted: Mon May 18, 2015 8:38 am ---- I am looking to change the cam belt on my 2000 RFR 206GTi, but I don't know where to get the locking tools from - my local dealer said they don't sell them. The only kits I have found work out at the kind of price I may as well pay someone to do it.
Where is a good place to buy / or even rent?
#2: Re: Cam and crankshaft locking tools - where from? Author: 206gt160, Location: BlackburnPosted: Mon May 18, 2015 8:40 am ---- I got some off eBay but I payed around 30/40 quid.
#3: Re: Cam and crankshaft locking tools - where from? Author: neilneil2000, Posted: Mon May 18, 2015 9:07 am ---- Don't suppose you could fading out the name of the seller or the kit could you? The ones I've been seeing are well over £100
#4: Re: Cam and crankshaft locking tools - where from? Author: 206gt160, Location: BlackburnPosted: Mon May 18, 2015 9:12 am ---- I will have to have a look next time I'm with the car.
#5: Re: Cam and crankshaft locking tools - where from? Author: 206gt160, Location: BlackburnPosted: Mon May 18, 2015 9:20 am ---- Spoox Motorsport £44.34 delivered off EBay.. 206 Gti timing pin kit
#6: Re: Cam and crankshaft locking tools - where from? Author: neilneil2000, Posted: Mon May 18, 2015 2:54 pm ---- Thanks, have just had a look at that. Mine is a very early model (W reg) so I'm expecting to need the crankshaft holding tool as well. What year is yours?
#7: Re: Cam and crankshaft locking tools - where from? Author: 206gt160, Location: BlackburnPosted: Mon May 18, 2015 3:05 pm ---- Mine is a 99 reg so V. I thought that kit was the full kit needed? Infact I'm 100 percent sure it is.
#8: Re: Cam and crankshaft locking tools - where from? Author: neilneil2000, Posted: Mon May 18, 2015 4:08 pm ---- Sweet, I'm doing it with my brother this weekend...time will tell whether or not this is a massive error!!!
#9: Re: Cam and crankshaft locking tools - where from? Author: 206gt160, Location: BlackburnPosted: Mon May 18, 2015 5:38 pm ---- If your doing the cambelt you should do the water pump at the same time. Take your time and have a manual with torque values to do everything back up to and it will be easy
#10: Re: Cam and crankshaft locking tools - where from? Author: Steve206, Location: UKPosted: Tue May 19, 2015 4:09 pm ---- Either 6mm or 8mm drill bits also work fine!
#11: Re: Cam and crankshaft locking tools - where from? Author: gazza82, Location: South BucksPosted: Thu May 21, 2015 5:00 am ---- There isn't much room to work so drill bits might be a bit nasty .. I used 6mm and 8mm hex headed screws when I did the CC's 138 engine ...
Isn't there a clip of some description for the lower crank that holds the belt in place? Didn't use one on the 138 but seem to remember seeing one related to the 180 engine.
#12: Re: Cam and crankshaft locking tools - where from? Author: 206gt160, Location: BlackburnPosted: Fri May 22, 2015 12:58 pm ---- Easier and safer to just spend 40 notes on a Spoox Motorsport cam locking/timing tool set.
We are not responsible for comments posted by our users, as they are the property of the poster
Interactive software released under GNU GPL,
Code Credits,
Privacy Policy
Membership:
Latest: 
New Today: 0
New Yesterday: 1
Overall: 17125
Online Now [78]:
Visitors: 77
Members: 0
Staff Online Now:
Page Views:
General
