 |
Author |
Message |
|
|
 Topic: Bleed screws. |
|
|
LeeThr
Replies: 12
Views: 7384
|
 Forum: 206 Problems Posted: Fri Nov 24, 2017 4:12 pm Subject: Re: Bleed screws. |
|
|
Use a proper flared brake union spanner and apply plenty of heat first. |
|
|
Topic: Bleed screws. |
|
|
LeeThr
Replies: 12
Views: 7384
|
Forum: 206 Problems Posted: Thu Nov 23, 2017 2:27 pm Subject: Re: Bleed screws. |
|
|
£18 for 4 bleed screws? Ouch.... |
|
|
Topic: Bleed screws. |
|
|
LeeThr
Replies: 12
Views: 7384
|
Forum: 206 Problems Posted: Wed Nov 22, 2017 11:09 am Subject: Re: Bleed screws. |
|
|
Brakes International |
|
|
Topic: problem with 206RC code Error: p0012 sounds diesel |
|
|
LeeThr
Replies: 6
Views: 5715
|
Forum: 206 Problems Posted: Fri Sep 15, 2017 4:38 pm Subject: Re: problem with 206RC code Error: p0012 sounds diesel |
|
|
If you've had the belt done, then could be the usual 180/RC issue that the exhaust cams jumped a tooth or two. |
|
|
Topic: Pre-Plexed BSi - What Does it Run? |
|
|
LeeThr
Replies: 8
Views: 4206
|
Forum: 206 Problems Posted: Wed Aug 30, 2017 5:53 pm Subject: Re: Pre-Plexed BSi - What Does it Run? |
|
|
Why not source a complete loom from an EW Xsara as well then? Throw the whole lot in. |
|
|
Topic: Pre-Plexed BSi - What Does it Run? |
|
|
LeeThr
Replies: 8
Views: 4206
|
Forum: 206 Problems Posted: Wed Aug 30, 2017 4:43 pm Subject: Re: Pre-Plexed BSi - What Does it Run? |
|
|
Indeed, could always go all out and run it on aftermarket management. I'd imagine the hardest part would be getting the engine mounts adjusted for the right angle for the EW lump compared to the XU. |
|
|
Topic: 206 HDi 2.0 2003 Super slack auxiliary belt |
|
|
LeeThr
Replies: 9
Views: 8462
|
Forum: 206 Problems Posted: Wed Aug 30, 2017 4:41 pm Subject: Re: 206 HDi 2.0 2003 Super slack auxiliary belt |
|
|
Could you not just swap the pulley off the old pump over? |
|
|
Topic: Pre-Plexed BSi - What Does it Run? |
|
|
LeeThr
Replies: 8
Views: 4206
|
Forum: 206 Problems Posted: Wed Aug 30, 2017 4:39 pm Subject: Re: Pre-Plexed BSi - What Does it Run? |
|
|
I'm going to go with the safe bet of a 205 |
|
|
Topic: 206 HDi 2.0 2003 Super slack auxiliary belt |
|
|
LeeThr
Replies: 9
Views: 8462
|
Forum: 206 Problems Posted: Tue Aug 29, 2017 3:15 am Subject: Re: 206 HDi 2.0 2003 Super slack auxiliary belt |
|
|
You've got the belt on the wrong way. It'll only sit tight and fit if it's in the exact layout it should be. Any other configuration and it's either too short or as youve found out seems too long.
... |
|
|
Topic: 206 1.4 2002 - ball joint dust covers, and emissions |
|
|
LeeThr
Replies: 2
Views: 2983
|
Forum: 206 Problems Posted: Fri Aug 18, 2017 9:59 am Subject: Re: 206 1.4 2002 - ball joint dust covers, and emissions |
|
|
Peugeot
361509 @ 1.76 each |
|
|
Topic: 206 Gti S16 dashboard question |
|
|
LeeThr
Replies: 4
Views: 24146
|
Forum: 206 Talk Posted: Tue Aug 01, 2017 10:47 pm Subject: Re: 206 Gti S16 dashboard question |
|
|
Shows how much oil's actually in the engine. |
|
|
Topic: timing belt |
|
|
LeeThr
Replies: 11
Views: 24021
|
Forum: 206 Talk Posted: Wed Mar 22, 2017 8:22 pm Subject: Re: timing belt |
|
|
[quote="gazza82"]2.0 diesel is easier than a 2.0 twincam petrol! :-)[/quote]
I've done both. |
|
|
Topic: timing belt |
|
|
LeeThr
Replies: 11
Views: 24021
|
Forum: 206 Talk Posted: Wed Mar 22, 2017 7:52 pm Subject: Re: timing belt |
|
|
Gates more often than not are the OE suppliers to Peugeot, i've pulled off factory belts badged up as Gates, and even gone into the parts counter at a main dealer and been given a Gates belt complete ... |
|
|
Topic: Abs fault |
|
|
LeeThr
Replies: 12
Views: 21132
|
Forum: 206 Talk Posted: Tue Mar 14, 2017 3:24 pm Subject: Re: Abs fault |
|
|
That's how mine started off, but I was able to clear the code in planet. But eventually it got to the point of the code always being there and would return instantly when cleared, then I had the ABS l ... |
|
|
Topic: Abs fault |
|
|
LeeThr
Replies: 12
Views: 21132
|
Forum: 206 Talk Posted: Tue Mar 14, 2017 1:51 pm Subject: Re: Abs fault |
|
|
That's the exact issue mine had. And I also have the mk70 unit.
All the hits online I was reading was giving me horror stories of a new pump being needed. I'm sure you can imagine the sense of reli ... |
|
|
|
|
Membership:
Latest: 
New Today: 0
New Yesterday: 0
Overall: 17134
Online Now [419]:
Visitors: 418
Members: 0
Staff Online Now:
Page Views:
General
Forums Home
Forum FAQ
Search
