 |
Author |
Message |
|
|
 Topic: Suspension 'clunk' |
|
|
SDK206
Replies: 5
Views: 1924
|
 Forum: 206 Problems Posted: Fri Apr 15, 2011 1:48 pm Subject: Re: Suspension 'clunk' |
|
|
possibly a CV joint has gone and has been for a while by what you say.
another possibility could be a seized strut top bearing but usually you would hear these more on turning when stationary like ... |
|
|
Topic: Spare Key stuck In Ignition.. |
|
|
SDK206
Replies: 19
Views: 4916
|
Forum: 206 Problems Posted: Tue Apr 12, 2011 2:26 pm Subject: Re: Spare Key stuck In Ignition.. |
|
|
yes i missed that bit mate cheers 
i was under the impression that it did turn just wouldnt release when at position 0, should of said first time eh! |
|
|
Topic: MOT failure |
|
|
SDK206
Replies: 11
Views: 3584
|
Forum: 206 Problems Posted: Tue Apr 12, 2011 7:48 am Subject: Re: MOT failure |
|
|
[quote="macca1411"]You can get a split CV boot kit which you glue along a tongue and groove seam. Saves taking the driveshaft out. I've used them before and never had a problem with them.[/quote]
i ... |
|
|
Topic: Spare Key stuck In Ignition.. |
|
|
SDK206
Replies: 19
Views: 4916
|
Forum: 206 Problems Posted: Mon Apr 11, 2011 12:35 pm Subject: Re: Spare Key stuck In Ignition.. |
|
|
are you able to remove the lower steering wheel cowling?
i so you should be able to get at the barrel to release the key |
|
|
Topic: seat going back while driving |
|
|
SDK206
Replies: 11
Views: 1900
|
Forum: 206 Problems Posted: Mon Apr 11, 2011 12:32 pm Subject: Re: seat going back while driving |
|
|
really common replaced loads of em! as someone said s**te french engineering
new runners, job done |
|
|
Topic: Spare Key stuck In Ignition.. |
|
|
SDK206
Replies: 19
Views: 4916
|
Forum: 206 Problems Posted: Mon Apr 11, 2011 12:26 pm Subject: Re: Spare Key stuck In Ignition.. |
|
|
not an auto is it?? |
|
|
Topic: newbie with problems fitting gearbox |
|
|
SDK206
Replies: 3
Views: 992
|
Forum: 206 Problems Posted: Mon Apr 11, 2011 7:05 am Subject: Re: newbie with problems fitting gearbox |
|
|
From what you have said about the cable not being easy to fit and you have swapped the clutch fork over, it would sound like this is where the problem is.
if the cable is mega tight it will pull on ... |
|
|
Topic: Forgot to open bleed ports |
|
|
SDK206
Replies: 9
Views: 1859
|
Forum: 206 Problems Posted: Sat Apr 09, 2011 2:43 pm Subject: Re: Forgot to open bleed ports |
|
|
yeah the thermostat, when it opens the level will drop slightly especially when just refilled
get the engine really hot and the fan will come on that will be proof its ok |
|
|
Topic: Wheel turns when braking.. |
|
|
SDK206
Replies: 6
Views: 1288
|
Forum: 206 Problems Posted: Sat Apr 09, 2011 2:13 pm Subject: Re: Wheel turns when braking.. |
|
|
also check trye pressures as this can have same effect if one is alot lower than the other |
|
|
Topic: Wheel turns when braking.. |
|
|
SDK206
Replies: 6
Views: 1288
|
Forum: 206 Problems Posted: Sat Apr 09, 2011 2:12 pm Subject: Re: Wheel turns when braking.. |
|
|
binding brake on one side?? possible cause sticking caliper slides, pads seized in carrier etc basically have them inspected as in the uk the balance of a cars brakes are tested on an MOT test and the ... |
|
|
Topic: Forgot to open bleed ports |
|
|
SDK206
Replies: 9
Views: 1859
|
Forum: 206 Problems Posted: Sat Apr 09, 2011 2:05 pm Subject: Re: Forgot to open bleed ports |
|
|
yeah i know what you mean, it takes ages but when i was in the trade we would never let a peugeot/citroen diesel leave the garage after work on cooling system without the fan cutting in!! |
|
|
Topic: Forgot to open bleed ports |
|
|
SDK206
Replies: 9
Views: 1859
|
Forum: 206 Problems Posted: Sat Apr 09, 2011 1:52 pm Subject: Re: Forgot to open bleed ports |
|
|
In all fairness if you have had coolant coming from the matrix end and its returning water to the header, its probably ok.
I'm no expert on the 1.4 hdi but i would of expected to see a bleed screw ... |
|
|
Topic: When i get in and turn on the ignition?!? |
|
|
SDK206
Replies: 23
Views: 4509
|
Forum: 206 Problems Posted: Fri Apr 01, 2011 9:37 am Subject: Re: When i get in and turn on the ignition?!? |
|
|
My dials do this too but usually after a couple of minutes driving they all drop back to rest then spring back into life!! also noticed that headlights blink when changing gear, especially after being ... |
|
|
Topic: Warbling noise after cambelt change |
|
|
SDK206
Replies: 14
Views: 3686
|
Forum: 206 Problems Posted: Thu Mar 31, 2011 3:46 pm Subject: Re: Warbling noise after cambelt change |
|
|
i've known a warbling noise to be an over-tensioned timing belt, not saying yours is but just incase the aux belt doesn't sort it |
|
|
Topic: air con |
|
|
SDK206
Replies: 5
Views: 1194
|
Forum: 206 Problems Posted: Sun Mar 27, 2011 10:28 am Subject: Re: air con |
|
|
there should be two fans although ive never noticed on a pug, usually one for the engine the other to assist when the air con is working |
|
|
|
|
Membership:
Latest: 
New Today: 0
New Yesterday: 1
Overall: 17131
Online Now [300]:
Visitors: 299
Members: 0
Staff Online Now:
Page Views:
General
Forums Home
Forum FAQ
Search
