 |
Author |
Message |
|
|
 Topic: Brake line nut |
|
|
marone
Replies: 5
Views: 2177
|
 Forum: 206 Problems Posted: Sun Jul 09, 2017 5:56 pm Subject: Re: Brake line nut |
|
|
Cheers for the tip Edward, I'll give that a go.
I'm from Wakefield Cube, I'm sure theres a few places that have them around here then. Might look to get it swapped out as its looking tired. |
|
|
Topic: Brake line nut |
|
|
marone
Replies: 5
Views: 2177
|
Forum: 206 Problems Posted: Sat Jul 08, 2017 5:54 pm Subject: Brake line nut |
|
|
Hi All
I'm attempting to replace the brake lines but I'm having difficulty removing the nut that connects the flexible hose to the solid pipe.
I have a set of flare nut wrenches but I'm finding ... |
|
|
Topic: Bonnet Sensor Problems |
|
|
marone
Replies: 10
Views: 1624
|
Forum: 206 Problems Posted: Sat Jul 11, 2015 11:26 am Subject: Re: Bonnet Sensor Problems |
|
|
Ok, I've bridged the connector on the loom and switched the engine on, so far its not reporting the bonnet is open. So that leads me back to the switch.
I don't have a multimeter available but I kn ... |
|
|
Topic: Bonnet Sensor Problems |
|
|
marone
Replies: 10
Views: 1624
|
Forum: 206 Problems Posted: Fri Jul 10, 2015 4:03 pm Subject: Re: Bonnet Sensor Problems |
|
|
Thanks, I've replaced the microswitch that's connected to the bonnet latch - is that the sensor you're talking about? If so unfortunately it didn't make a difference. Do you think it could be the rest ... |
|
|
Topic: Bonnet Sensor Problems |
|
|
marone
Replies: 10
Views: 1624
|
Forum: 206 Problems Posted: Fri Jul 10, 2015 2:37 pm Subject: Re: Bonnet Sensor Problems |
|
|
Looks like the button gets half depressed when the catch is down (without any remaining force applied).
Also tried fully depressing the switch but it still reports that the bonnet is open. |
|
|
Topic: Bonnet Sensor Problems |
|
|
marone
Replies: 10
Views: 1624
|
Forum: 206 Problems Posted: Fri Jul 10, 2015 1:18 pm Subject: Re: Bonnet Sensor Problems |
|
|
I believe it is.
What do you suggest, closing the catch whilst the bonnet is still up and check that it's making enough contact with the switch? |
|
|
Topic: Bonnet Sensor Problems |
|
|
marone
Replies: 10
Views: 1624
|
Forum: 206 Problems Posted: Fri Jul 10, 2015 12:49 pm Subject: Bonnet Sensor Problems |
|
|
I'm having an issue with the bonnet on my 206.
On hot days when driving I get a bleep followed by the dash suggesting the bonnet has opened, this is causing a slight annoyance. Additionally to this ... |
|
|
Topic: Wishbone Fitting Problems |
|
|
marone
Replies: 9
Views: 2198
|
Forum: 206 Problems Posted: Mon Aug 25, 2014 6:37 am Subject: Re: Wishbone Fitting Problems |
|
|
Finally managed it, phew!
I'll probably be slated for this and I'm not suggesting other do this... but the subframe was just that little too tight to get the rear bush in (we're taking a single mm ... |
|
|
Topic: Wishbone Fitting Problems |
|
|
marone
Replies: 9
Views: 2198
|
Forum: 206 Problems Posted: Sun Aug 24, 2014 2:22 pm Subject: Re: Wishbone Fitting Problems |
|
|
Sorry I mean height rather than width.
Its a whole new arm from Peugeot Sport so it would have been done in the factory I guess. I'll try and get a photo up. |
|
|
Topic: Wishbone Fitting Problems |
|
|
marone
Replies: 9
Views: 2198
|
Forum: 206 Problems Posted: Sun Aug 24, 2014 2:11 pm Subject: Re: Wishbone Fitting Problems |
|
|
Doesn't seem to, no. Its the same width as the middle bush, which is the same metal bush used in the normal arms |
|
|
Topic: Wishbone Fitting Problems |
|
|
marone
Replies: 9
Views: 2198
|
Forum: 206 Problems Posted: Sun Aug 24, 2014 1:26 pm Subject: Re: Wishbone Fitting Problems |
|
|
Turning into a bit of a nightmare. Still cannot get the new arm fitted, the outer bush looks to be about a millimetre too wide to fit in the subframe. All I end up doing is wedging in the bush at an a ... |
|
|
Topic: Wishbone Fitting Problems |
|
|
marone
Replies: 9
Views: 2198
|
Forum: 206 Problems Posted: Sun Aug 24, 2014 4:16 am Subject: Re: Wishbone Fitting Problems |
|
|
I think the only difference is the centre material used within the bushes.
I'll be giving it another go today. Hopefully I'll have more joy! |
|
|
Topic: Wishbone Fitting Problems |
|
|
marone
Replies: 9
Views: 2198
|
Forum: 206 Problems Posted: Sat Aug 23, 2014 1:13 pm Subject: Wishbone Fitting Problems |
|
|
Hi All
I'm attempting to replace the offside wishbone but I'm having some difficulty getting the replacement to fit into the subframe. I cannot seem to get the far side bush to slide into its 'slot ... |
|
|
Topic: Wishbone Bolts |
|
|
marone
Replies: 4
Views: 1510
|
Forum: 206 Problems Posted: Mon Aug 11, 2014 8:35 am Subject: Re: Wishbone Bolts |
|
|
As simple as that. Excellent.
Cheers |
|
|
Topic: Wishbone Bolts |
|
|
marone
Replies: 4
Views: 1510
|
Forum: 206 Problems Posted: Mon Aug 11, 2014 7:35 am Subject: Wishbone Bolts |
|
|
I'm planning on changing over my wishbones in the coming weeks.
I've got the new arms but I want to replace the bolts with new ones. Problem is I not sure which bolts I need and how many.
Thus ... |
|
|
|
|
Membership:
Latest: 
New Today: 0
New Yesterday: 0
Overall: 17130
Online Now [327]:
Visitors: 326
Members: 0
Staff Online Now:
Page Views:
General
Forums Home
Forum FAQ
Search
