|
Author
|
Message |
|
|
 Posted: Sun Jan 27, 2013 8:05 am |
|
|
|
|
Joined: Nov 07, 2012
Posts: 87
Trade Rating: 0
Location: st.albans hertfordshire
|
 |
Basically I put an induction kit in my car, but now when I accelerate past 70mph my car seems too go over the halway mark and overheat. Then when I slow down my temperature gauge drops to cold... Isn't it supposed to be the other way around ? Anyone have any solutions as too how too fix this problem ? Thankyou
| |  |
|
|
 |
|
|
|
|
|
|
Posted: Sun Jan 27, 2013 8:16 am |
|
|
|
|
Joined: Dec 19, 2012
Posts: 365
Trade Rating: 0
Location: Sussex
|
|
is it an open cone filter
| | |
|
|
|
|
|
|
|
|
|
|
Posted: Sun Jan 27, 2013 8:30 am |
|
|
|
|
Joined: Nov 07, 2012
Posts: 87
Trade Rating: 0
Location: st.albans hertfordshire
|
|
Yup, with a silicone hose coming of the induction pipe for the breather
| | |
|
|
|
|
|
|
|
|
|
|
Posted: Sun Jan 27, 2013 9:22 am |
|
|
|
|
Joined: Dec 19, 2012
Posts: 365
Trade Rating: 0
Location: Sussex
|
|
there's alot of debate about open filters but all i know is the engine will suffer from heat soak, unless a cold air feed is fitted. Dont know if this is the main cause of overheating someone else might be able to help 
| | |
|
|
|
|
|
|
|
|
|
|
Posted: Sun Jan 27, 2013 9:35 am |
|
|
|
|
Joined: Aug 04, 2011
Posts: 1343
Trade Rating: 0
Location: Swindon
|
|
The first step is to revert to your original induction system and see if that fixes it. Until you do that you don't know if it definitely is the induction system that is making it overheat or a coincidental failure of head gasket, thermostat or header tank screw cap. Also check the coolant level - you could have damaged a hose while fitting the induction system.
If your induction is close to the exhaust then it will be sucking hot air straight into the engine possibly causing the over heat and sucking hot air will also reduce power even if it wasn't over heating. So many cone intakes reduce power simply because they are sucking hot air straight from the engine bay. Once running and for maximum power you want the air going into the engine to be as cold as possible.
That is the thing with the original design. It might be a bit restrictive and go through a few bends but at least it is sucking cold air.
| | |
|
|
|
|
 | |  |
| Morris 1000, Austin 1100, Escort Mk2, Fiat Mirafiori, Alfa 33, Alfa GT Junior, Alfasud, Alfetta GTV (2x), Alfa 164 3.0 V6, Alfa 164 2.0, Alfa 75 V6, Alfa 156 2.4 (diesel remapped 200bhp), Alfa 147 GTA (3.6 295bhp), Alfa 159 (diesel remapped 245bhp 300ft.lbs @ 2500rpm)
Why isn't my daughter an Alfaholic? | |
 | |  |
|
|
|
|
|
|
|
Posted: Sun Jan 27, 2013 11:09 am |
|
|
|
|
Joined: Nov 07, 2012
Posts: 87
Trade Rating: 0
Location: st.albans hertfordshire
|
|
i put the induction kit right where the original manufactures one was, and its just simply swapped a floppy pipe with a stiff one, with a cone on the end of it, do you think it is worth putting an cold air intake feed into the front grill ?
| | |
|
|
|
|
|
|
|
|
|
|
Posted: Sun Jan 27, 2013 12:29 pm |
|
|
|
|
Joined: Jan 23, 2013
Posts: 10
Trade Rating: 0
Location: south london
|
|
YES. Either that or use some ducting to relocate the filter to the top of the intake side, cut a hole where the bonnet vents are and duct straight to the filter. Or leave it as is, take out a fog and get the ducting in there!
| | |
|
|
|
|
| | |
| If you cant cable tie it, it's well and truly f****d | |
| | |
|
|
|
|
|
Membership:
Latest: 
New Today: 0
New Yesterday: 0
Overall: 17129
Online Now [291]:
Visitors: 290
Members: 0
Staff Online Now:
Page Views:
General
Forums Home
Forum FAQ
Search
