#31: Re: RC track car Author: SAB206, Location: North WestPosted: Tue May 03, 2011 3:08 pm ----
Mr_Cellexe wrote:
rttam wrote:
thats what the 180/rc engine looks like without the engine cover on
granted they are almost identical. just something about it that gives of a deffo 138 vibe!
Need a proper enigne bay shot to confirm
It is definitely the EW10J4S GTI180 lump.
#32: Re: RC track car (update) Author: shell-vt, Location: durhamPosted: Thu May 05, 2011 7:13 am ---- very nice hope ours looks as good as this when finished
#33: Re: RC track car (update) Author: Edward, Location: In the garagePosted: Thu May 05, 2011 10:45 am ----
simpsonrc wrote:
the trumpets are 30mm i think i'm goning to try them an see how they work first. i will get a pictuer of them with my custom rad.
Jenvey website wrote:
What is the correct overall system length?
A guide figure, from the face of the trumpet to the centre of the valve head is 350mm for a 9,000 RPM engine. Other RPM are proportional i.e. for 18,000 RPM the figure is approximately 175mm.
#34: Re: RC track car (update) Author: simpsonrc, Location: coventryPosted: Thu May 05, 2011 12:10 pm ---- ye i have seen this, i think my setup has a total lenght of 340-330mm. So was think of trying 70mm trumpets i will have a play with them when its on the rollers so i can see how much difrence it makes.
#35: Re: RC track car (update) Author: simpsonrc, Location: coventryPosted: Fri Jun 17, 2011 1:16 pm ---- the new rad an oil cooler.
[img]
[/img]
[img]
[/img]
#36: Re: RC track car Author: orribleoldgit, Location: milton keynesPosted: Sat Jun 18, 2011 6:33 am ----
DJ- wrote:
Nice! wonder why they used an 206 rc for security!
You may laugh but my mrs got her 206 from andrews family garage in coventry and when its really dirty you can vaguely see securicor on the drivers door,so there must some use other than womens shopping cars!!!!
#37: Re: RC track car Author: orribleoldgit, Location: milton keynesPosted: Sat Jun 18, 2011 6:35 am ----
Cr4zYb0y wrote:
If your saving weight, surely you don't wanna pick the 180's..?
im turning my2.0hdi into a track weapon mate,so i think ill have to strip it down to a shell with a steering wheel,speedo pod and a seat
#38: Re: RC track car (update) Author: Edward, Location: In the garagePosted: Sat Jun 18, 2011 8:25 am ---- Just looking at your ITG filter. What sort of back plate does it use? A flat one or the deeper box like plate? How much clearance is between it and the power steering pump?
Do you have any pictures?
#39: Re: RC track car (update) Author: simpsonrc, Location: coventryPosted: Mon Jun 20, 2011 11:45 am ---- [img]
[/img]
#40: Re: RC track car (update) Author: Edward, Location: In the garagePosted: Mon Jun 20, 2011 2:17 pm ---- So does it use a backplate? Doesn't look like ones is attached between trumpets and bodies.
#41: Re: RC track car (update) Author: simpsonrc, Location: coventryPosted: Tue Jun 21, 2011 1:08 pm ---- no it dosent use one, it has four holes in the back of it an you strech them over the bell mouths. Not perfect but there good for tight spaces.
#42: Re: RC track car (update) Author: simpsonrc, Location: coventryPosted: Sat Jul 02, 2011 9:07 am ---- A little video of her being mapped.
Almost finshed for now, just need to finsh the mapping on the dnyo, get the race technologies dash working, put the cage back in and give her a clean. Then off to the track
#43: Re: RC track car (update) Author: glenpring, Location: KENTPosted: Sun Jul 03, 2011 10:33 am ---- do you have rear seats i thought you had taken them out lol
#44: Re: RC track car (update) Author: simpsonrc, Location: coventryPosted: Mon Jul 04, 2011 4:58 pm ---- lol no it don't have any rear seats.
Just wired up a wheel speed sensor for the dash and launch control.
#45: Re: RC track car (update) Author: simpsonrc, Location: coventryPosted: Mon Aug 01, 2011 4:32 pm ---- Car is back together now an going for its first out this year on sunday.
The race technology dash 2 is all working from the dta's can streem and she has been mapped an gose well, still got to be put on the rollers to be fine tuned tho. Ill get some pics.
We are not responsible for comments posted by our users, as they are the property of the poster
Interactive software released under GNU GPL,
Code Credits,
Privacy Policy
Membership:
Latest: 
New Today: 0
New Yesterday: 0
Overall: 17129
Online Now [73]:
Visitors: 72
Members: 0
Staff Online Now:
Page Views:
General
[/img]
[/img]
im turning my2.0hdi into a track weapon mate,so i think ill have to strip it down to a shell with a steering wheel,speedo pod and a seat 
[/img]
