#241: Re: Northantsben's xs project, (PG16 last update) Author: NorthantsBen, Location: Raunds, NorthamptonshirePosted: Thu Dec 29, 2011 3:34 pm ----
Ghosty wrote:
question, can the morrette lights be swapped around, like putting the high beam next to the indicator, and the dipped beam on the outside. looks like it can ????
Poss but I'm unsure never looked, just the sidelight bulb I'm thinking of dunno if it goes through case or not cant rember,
I bet dj would know.
#242: Re: Northantsben's xs project, (PG16 last update) Author: DJ-, Location: UKPosted: Thu Dec 29, 2011 4:21 pm ---- Probably not as standard as im sure the sizes of the optics are different.
You could probably make the middle optic slot bigger to hold the high beam though then fiberglass the outer optic holder to make it smaller or something? I see it being very difficult if not impossible!
Oh and good stuff Ben, seems like yesterday I remember it being on ebay and white! Nice to see progress!
#243: Re: Northantsben's xs project, (PG16 last update) Author: NorthantsBen, Location: Raunds, NorthamptonshirePosted: Thu Dec 29, 2011 4:37 pm ---- Haha still your fault dj
#244: Re: Northantsben's xs project, (PG16 last update) Author: NorthantsBen, Location: Raunds, NorthamptonshirePosted: Tue Jan 03, 2012 12:35 pm ----
#245: Re: Northantsben's xs project, (PG17 last update) Author: Gazza, Location: OSWESTRYPosted: Tue Jan 03, 2012 2:17 pm ---- Hay just looked through your whole thread, cars come a long way since you brought it, good job so far mate,
NorthantsBen wrote:
nice ride hight ....................
(is not on any jacks or anything )
had to put wheels on car to move it for some work to be done on house just shows how heavy an engine is
i think you'll find its the springs that are weak/soft as the engines aint that heavy mate
#246: Re: Northantsben's xs project, (PG17 last update) Author: craigdmjv, Location: WiltshirePosted: Tue Jan 03, 2012 3:15 pm ---- looks good that mate need a smoothed grill though
#247: Re: Northantsben's xs project, (PG17 last update) Author: NorthantsBen, Location: Raunds, NorthamptonshirePosted: Wed Jan 04, 2012 12:10 pm ----
Gazza wrote:
Hay just looked through your whole thread, cars come a long way since you brought it, good job so far mate,
i think you'll find its the springs that are weak/soft as the engines aint that heavy mate
thanks
well its quite heavy, just the iron block on its own i found it a job to move, and i lift heavy stuff at work so used to lifting/moving heavy stuff lol all fun
craigdmjv wrote:
looks good that mate need a smoothed grill though
yer going to just put a honey cone grill in i think,
on a plus side fitting the coilovers tomoro if im not home late from work or cba lol
#248: Re: Northantsben's xs project, (PG17 last update) Author: NorthantsBen, Location: Raunds, NorthamptonshirePosted: Sun Jan 08, 2012 12:48 pm ---- before (jack only there holding bumper up) ........
after.....
and the car wedged on gate post have to put car on two trolly jacks and roll it to get it over gate post
#249: Re: Northantsben's xs project, (PG17 last update) Author: Harry, Location: StaffordPosted: Sun Jan 08, 2012 12:53 pm ---- Starting to come together really nice and the stance is pretty perfect
#250: Re: Northantsben's xs project, (PG17 last update) Author: NorthantsBen, Location: Raunds, NorthamptonshirePosted: Sun Jan 08, 2012 12:56 pm ----
Harry wrote:
Starting to come together really nice and the stance is pretty perfect
thanks
rear is little high and also little un-level (left higher than right) but all the rest is more important 1st.
new door and some welding should be ready for paint then
#251: Re: Northantsben's xs project, (PG17 last update) Author: craigdmjv, Location: WiltshirePosted: Sun Jan 08, 2012 2:10 pm ---- needs aero wipers soon as it gets resprayed lol
#252: Re: Northantsben's xs project, (PG17) NOW lowered :D Author: NorthantsBen, Location: Raunds, NorthamptonshirePosted: Sun Jan 08, 2012 3:00 pm ---- had they would be at the bottom of my shopping list tbh craig, lot more to spend on 1st
#253: Re: Northantsben's xs project, (PG17) NOW lowered :D Author: kurosagi01, Location: NorthamptonPosted: Sun Jan 08, 2012 3:02 pm ---- Almost there man just need get yourself a new bonnet since that one there is damaged. Last bit of primer and then spray the car colour of your choice.
#254: Re: Northantsben's xs project, (PG17) NOW lowered :D Author: 00budham00, Location: IpsPosted: Sun Jan 08, 2012 5:35 pm ---- thought of the colour yet ?
#255: Re: Northantsben's xs project, (PG17) NOW lowered :D Author: NorthantsBen, Location: Raunds, NorthamptonshirePosted: Mon Jan 09, 2012 5:09 am ----
kurosagi01 wrote:
Almost there man just need get yourself a new bonnet since that one there is damaged. Last bit of primer and then spray the car colour of your choice.
lol i keep forgetting about that one gotta get a new one some point.
00budham00 wrote:
thought of the colour yet ?
yes and no as i have thought of loads of colours and they have all changed lol, sure it will change again by end of week
We are not responsible for comments posted by our users, as they are the property of the poster
Interactive software released under GNU GPL,
Code Credits,
Privacy Policy
Membership:
Latest: 
New Today: 0
New Yesterday: 0
Overall: 17130
Online Now [166]:
Visitors: 165
Members: 0
Staff Online Now:
Page Views:
General
)
just shows how heavy an engine is 
