#16: Re: ushers project (WIP) Author: usher, Location: northallertonPosted: Mon Apr 11, 2011 4:12 am ---- yet more bad news lol the cam followers came but for a vw so waiting for the right ones to come
bit of a newsense as i paid for next day delivery
#17: Re: ushers project (WIP) Author: Quarmbo, Location: Bristol & LeicesterPosted: Fri Apr 15, 2011 6:09 am ---- And ask for the delivery charge back then!
#18: Re: ushers project (WIP) Author: Callum206, Location: West SussexPosted: Fri Apr 15, 2011 11:52 am ---- Looking good man keep it up
#19: Re: ushers project (WIP) Author: craigy00craig, Location: surreyPosted: Fri Apr 15, 2011 12:36 pm ---- ive got the same sub, but only one. Looks really nice over all.
#20: Re: ushers project (WIP) Author: sam-c, Location: Uni: Kent Home: ScunthorpePosted: Fri Apr 15, 2011 12:44 pm ---- i could og on all day about the problems with your proposed audio plans but it seems my advice would be falling on deaf ears so i wont waste my time
however, in the interest of safety as said use 0 guage and then a fused distribution block into 4 x 4guage and i would also use an unfused distribution block in the same way for the ground wires
#21: Re: ushers project (WIP) Author: usher, Location: northallertonPosted: Sun Apr 17, 2011 1:08 pm ---- didnt ask for money back as they sent the new ones 24h, should be done tomorrow hopefully problem is now there fitting it inbetween other car book ins
as for the power wire i will be ready for the i told you so moment if anything does happen for this year all i will have in is one amp and the 2 12s as i have not finished the door cards parcel shelf etc
#22: Re: ushers project (WIP) Author: usher, Location: northallertonPosted: Wed Apr 20, 2011 1:25 pm ---- got the car back yesterday finally after a month of problems
gotta be gentle for a few hundred miles as yet so cant comment on the performance but the car is running sweet now only problem is there is some knocking as though something is loose / tapping when trying to start the car but not when running so will take it back to see what they think it could be but £160 for timing belt, water pump, cams, followers, aux belt and handbrake cables you cant go wrong also they had the car for 2weeks while waiting for parts etc
#23: Re: ushers project (WIP) Author: usher, Location: northallertonPosted: Fri Apr 22, 2011 6:50 am ---- managed to do 200 miles since tues lol, had a blast today and noticed a slight increase in power in the region 3-5k sure they will work better with a re-map
#24: Re: ushers project (WIP) Author: usher, Location: northallertonPosted: Mon Apr 25, 2011 3:20 pm ---- gave the car its 1st clean of the year (hangs head in shame) so thought i would try using my new machine polisher
how bad it was
i jet washed then hand washed to make sure i hade a good clean base
then went on to clean off all the tar that had built up
after this i set out claying the car ready for polishing
this is the result
i used auto glym SRP with the polisher and intensive tar remover and maguires clay
#25: Re: ushers project (WIP) cleaned update pg2 Author: Ali_H, Location: Chichester, SussexPosted: Mon Apr 25, 2011 3:28 pm ---- Thought your tyre was flat in the last one lol. And some of your photos are upside down
#26: Re: ushers project (WIP) cleaned update pg2 Author: usher, Location: northallertonPosted: Tue Apr 26, 2011 11:45 am ---- lol i tried to get them the right way round but wouldnt do it
does look flat
next plan is to wax it and detail more ie door hinges and start on the engine bay
#27: Re: ushers project (WIP) REMAPPED Author: usher, Location: northallertonPosted: Mon May 23, 2011 8:30 am ---- just got back from rs tuning where i had the car remapped and what a difference i now have a smooth power curve with correct fuel to air ration and gained 10bhp
overall im running near as damit 150bhp and the flywheel he tried to get it up to 150 but it wouldnt do it
graphs:-
before and after tacho was out though
before and after with fuel ratio again tacho is out my fueling was way out
after torque and hp one of the last runs did get 149.7 i think
after wheel power and fuel ratio
#28: Re: ushers project (WIP) REMAPPED Author: usher, Location: northallertonPosted: Fri Aug 26, 2011 2:26 pm ---- bit late but this is what i got done before the french car show
morretts fitted after owning them for over a year lol
engine bay cleaned
before
after
then after these pics i decided to re paint the covers black as they were looking a bit rough
while at FCS i went on the track and cooked my brakes the discs were purple for months, stopped the anoying squeel you get from brombos though
so next on the list is the 406 master cylinder and braided hoses followed by some bigger discs probably have to be custom made not sure yet, after that next year im not going to FCS but the year after i am with hopefully way better suspension set up thicker rear ARB torsion bars and adjustable dampers Last edited by usher on Fri Mar 09, 2012 6:55 am; edited 3 times in total
#29: Re: ushers project cleaned bay and moretts fitted Author: Katie206, Location: PlymouthPosted: Sat Aug 27, 2011 7:35 am ---- i've fallen in love with the colour! i want!! the gloss black trims compliment it really well good work
#30: Re: ushers project cleaned bay and moretts fitted Author: usher, Location: northallertonPosted: Sun Aug 28, 2011 1:34 pm ---- thanks i cant get enough of the colour
forgot to mention i have added 2 12"subs with 2 amps built in temp for now
also got my parcel shelf painted even though it needs more filling
We are not responsible for comments posted by our users, as they are the property of the poster
Interactive software released under GNU GPL,
Code Credits,
Privacy Policy
Membership:
Latest: 
New Today: 0
New Yesterday: 0
Overall: 17129
Online Now [77]:
Visitors: 76
Members: 0
Staff Online Now:
Page Views:
General
good work 
