#1: torsion bar Author: Seabook, Posted: Sat Mar 26, 2011 6:03 pm ---- manage to loose the torsion bars on the disc axle (finally)
just wonder which way/ direction should i take out the whole torsion bar? (if you know what i mean lol)
#2: Re: torsion bar Author: Addaz, Location: SuffolkPosted: Sat Mar 26, 2011 6:06 pm ---- From the passengers side you knock out the drivers (bottom one)
Knock from the drivers to the passengers (top one)
Off set washers out?
Also they can knock out either way, you just cant take them out doing the opposite way to the above
#3: Re: torsion bar Author: cartoonhead, Location: North ManchesterPosted: Sat Mar 26, 2011 6:07 pm ---- narr , just so the splines aint catching.
just make sure to clean the splines on the bar and where it fits and get some copper grease on there and if its needs to be adjusted again it takes 15 min
#4: Re: torsion bar Author: Seabook, Posted: Sat Mar 26, 2011 6:08 pm ----
Addaz wrote:
From the passengers side you knock out the drivers (bottom one)
Knock from the drivers to the passengers (top one)
Off set washers out?
Also they can knock out either way, you just cant take them out doing the opposite way to the above
nono
i have already knock out the torsion bars,
i just need to remove the bars from the axle completely
#5: Re: torsion bar Author: Addaz, Location: SuffolkPosted: Sat Mar 26, 2011 6:09 pm ---- Top part of my message then mate
#6: Re: torsion bar Author: Seabook, Posted: Sat Mar 26, 2011 6:11 pm ---- simple pics lol +-----+ is the torsion bar, | is the trailing arm
right arm|+---------+| left arm (before)
right arm +---|---+| left arm (now)
which way should i take out the torsion bars?
#7: Re: torsion bar Author: Seabook, Posted: Sat Mar 26, 2011 6:12 pm ----
Addaz wrote:
Top part of my message then mate
so that means i just keep knocking them in the same diection?
would it not damage the thread? as left and right is different?
because i remember when macj fit my torsion bar he install the bar from the middle..... Last edited by Seabook on Sat Mar 26, 2011 6:13 pm; edited 1 time in total
#8: Re: torsion bar Author: cartoonhead, Location: North ManchesterPosted: Sat Mar 26, 2011 6:12 pm ---- they should just slide out the way you have knocked them.
clean the end up before tryin to get them out.
#9: Re: torsion bar Author: cartoonhead, Location: North ManchesterPosted: Sat Mar 26, 2011 6:13 pm ----
Seabook wrote:
Addaz wrote:
Top part of my message then mate
so that means i just keep knocking them in the same diection?
Yup
#10: Re: torsion bar Author: Seabook, Posted: Sat Mar 26, 2011 6:19 pm ---- ok thz, anyway can't do it now....
have to wait until morning lol
#11: Re: torsion bar Author: Addaz, Location: SuffolkPosted: Sat Mar 26, 2011 6:23 pm ---- Left to right is different
As it only fits one way, coming out of the axle, one end is bigger
I found this out when i stripped down my axel
Top tortion bar
+++|++++ | (drivers side)
Lower tortion bar
| ++++|+++ (drivers side)
#12: Re: torsion bar Author: Seabook, Posted: Sat Mar 26, 2011 6:27 pm ----
Addaz wrote:
Left to right is different
As it only fits one way, coming out of the axle, one end is bigger
I found this out when i stripped down my axel
Top tortion bar
+++|++++ | (drivers side)
Lower tortion bar
| ++++|+++ (drivers side)
nice one addaz, i know what to do now
#13: Re: torsion bar Author: 80brett, Location: WAKEFIELDPosted: Sun Mar 27, 2011 3:24 am ---- haha
#14: Re: torsion bar Author: kieron, Location: in the housePosted: Sun Mar 27, 2011 3:30 am ---- this was of a 306 from years ago buts sames kind of things as 206
We are not responsible for comments posted by our users, as they are the property of the poster
Interactive software released under GNU GPL,
Code Credits,
Privacy Policy
Membership:
Latest: 
New Today: 0
New Yesterday: 0
Overall: 17130
Online Now [109]:
Visitors: 108
Members: 0
Staff Online Now:
Page Views:
General
