#1: fan belt wont fit Author: dumdum0910, Location: letchworthPosted: Sat May 28, 2011 4:49 pm ---- i am on my 2nd fan belt . i got this 1 from peugeot but i cannot get it to go over the tensioner. i pull it back all the way with a spanner but it seems to short, but when i put it up against the old 1 its the same peugeot say there is only 1 length for this engine. any ideas? ive tried soaking it in hot water to try and soften it up
i have a 1.1 look
#2: Re: fan belt wont fit Author: nakednakeddave, Location: aberdeenPosted: Sat May 28, 2011 5:56 pm ---- put a 3/8 ratchet with a bar in the hole next to the tensoiner when the belt of almost in the right position and pushe the ratchet and should move enough to slip on.
#3: Re: fan belt wont fit Author: dumdum0910, Location: letchworthPosted: Sun May 29, 2011 3:49 am ---- what hole do you mean? i cant see any hole?
#4: Re: fan belt wont fit Author: dumdum0910, Location: letchworthPosted: Sun May 29, 2011 4:24 am ----
were would this hole be? the top tensioner is the 1 you put a 13mm spanner on to move the tensioner in and out
#5: Re: fan belt wont fit Author: richpowell91, Location: Melton Mowbray LeicestershirePosted: Sun May 29, 2011 5:11 am ---- Do you have an automatic tensioner or a manual tensioner? If you have an automatic tensioner then there will be a square hole to the left of the roller pictured.
there's a good guide, the bottom picture shows the hole if it has an automatic tensioner.
#6: Re: fan belt wont fit Author: dumdum0910, Location: letchworthPosted: Sun May 29, 2011 5:20 am ---- www.peugeot206cc.co.uk...-k06sc.gif its this 1 but it doesnt have the spring between the tensioner and crankshaft pulley
#7: Re: fan belt wont fit Author: dumdum0910, Location: letchworthPosted: Sun May 29, 2011 5:30 am ---- also i dont have any adjuster on the alternater
#8: Re: fan belt wont fit Author: richpowell91, Location: Melton Mowbray LeicestershirePosted: Sun May 29, 2011 5:40 am ---- Ah okay sorry ignore all that then, have you tried putting the old on back on again to make sure there isnt a problem with the tensioner?
#9: Re: fan belt wont fit Author: dumdum0910, Location: letchworthPosted: Sun May 29, 2011 5:41 am ---- yep got the old 1 on. the old 1 goes straight on with no problem so im confused.
#10: Re: fan belt wont fit Author: Timon2210, Location: PalestinePosted: Sun May 29, 2011 5:42 am ----
dumdum0910 wrote:
also i dont have any adjuster on the alternater
That is impossible,it's a must,and do as the guys said above,other wise the belt would be lose,and slip out while you drive,it have to be tight to work well.
#11: Re: fan belt wont fit Author: dumdum0910, Location: letchworthPosted: Sun May 29, 2011 5:44 am ---- the top tensioner is spring loaded . the alternator is bolted straight on to the block
#12: Re: fan belt wont fit Author: Lee, Location: EnglandPosted: Sun May 29, 2011 5:57 am ----
dumdum0910 wrote:
i am on my 2nd fan belt . i got this 1 from peugeot but i cannot get it to go over the tensioner. i pull it back all the way with a spanner but it seems to short, but when i put it up against the old 1 its the same peugeot say there is only 1 length for this engine. any ideas? ive tried soaking it in hot water to try and soften it up
i have a 1.1 look
Firstly do you need two threads for the same problem?
Secondly, if they used your chassis number then there will only be one belt to fit your car.
And I've just emailed you a guide to your msn address
We are not responsible for comments posted by our users, as they are the property of the poster
Interactive software released under GNU GPL,
Code Credits,
Privacy Policy
Membership:
Latest: 
New Today: 1
New Yesterday: 0
Overall: 17131
Online Now [56]:
Visitors: 55
Members: 0
Staff Online Now:
Page Views:
General
peugeot say there is only 1 length for this engine. any ideas? ive tried soaking it in hot water to try and soften it up
were would this hole be? the top tensioner is the 1 you put a 13mm spanner on to move the tensioner in and out
