#1: Cant go lower? Author: Addaz, Location: SuffolkPosted: Sat Jun 18, 2011 1:28 pm ---- Right peoples,
I have a big problem, the rear needs to drop more but the arm will be resting on the chassis stopping it
Is there a way round this?
Plus i will be removing the helper springs and winding her down fully, i already have the smallest possible tyres. The coilovers are racelands, is there a other coilovers that can go lower or will i need shorter springs?
Thanks
Adam
#2: Re: Cant go lower? Author: Seabook, Posted: Sat Jun 18, 2011 1:32 pm ---- front: yes, you will need shorter spring and make sure get the harder spring too.
rear: i don't know.
#3: Re: Cant go lower? Author: Abzynthe, Posted: Sat Jun 18, 2011 2:19 pm ---- Just take the suspension off altogether
#4: Re: Cant go lower? Author: arronmee1990, Location: Broughton AstleyPosted: Sat Jun 18, 2011 2:30 pm ---- Don't know about the rear but on the front you could raise the top mount higher to go even lower (if that makes sense)
#5: Re: Cant go lower? Author: EdCherry, Location: WiltshirePosted: Sat Jun 18, 2011 2:37 pm ---- You can modify the mounts on most pugs to change the ride height. Specially on the olders ones, requires a fair bit of fabrication and often some welding on the car but it does the job.
Of course the arms wont move lower if they are already on the bumpstops and you dont remove them and work the chassis rail.
#6: Re: Cant go lower? Author: -Dave-, Location: North ManchesterPosted: Sat Jun 18, 2011 2:38 pm ---- Airbag's FTW
#7: Re: Cant go lower? Author: Addaz, Location: SuffolkPosted: Sat Jun 18, 2011 2:41 pm ----
EdCherry wrote:
You can modify the mounts on most pugs to change the ride height. Specially on the olders ones, requires a fair bit of fabrication and often some welding on the car but it does the job.
Of course the arms wont move lower if they are already on the bumpstops and you dont remove them and work the chassis rail.
Ive removed the bump stops.....
So yes it will be on the chassis rail, but i dont quite get what you mean by 'you dont remove them'?
#8: Re: Cant go lower? Author: EdCherry, Location: WiltshirePosted: Sat Jun 18, 2011 2:42 pm ---- For example if the car was already on the bumpstops, and you modified the mounts to go lower, the car would not go lower cause it still has to sit on those bumpstops. Same if you've moved them and your sitting on the chassis rails. Get the welder out.
#9: Re: Cant go lower? Author: Addaz, Location: SuffolkPosted: Sat Jun 18, 2011 2:44 pm ----
EdCherry wrote:
For example if the car was already on the bumpstops, and you modified the mounts to go lower, the car would not go lower cause it still has to sit on those bumpstops. Same if you've moved them and your sitting on the chassis rails. Get the welder out.
I removed them to go lower
So basically the chassis needs to be altered slightly, or could if the arm tubing (where they sit on the axle?) be extended/spaced to give that clearence?
#10: Re: Cant go lower? Author: arronmee1990, Location: Broughton AstleyPosted: Sat Jun 18, 2011 3:17 pm ---- How come you need to go lower than flush with chassis rail on the back anyway?
Surely the sill will be on the floor?
#11: Re: Cant go lower? Author: tomd0801754, Location: MoscowPosted: Sat Jun 18, 2011 3:47 pm ---- His aim will be about 10mm clearance.
#12: Re: Cant go lower? Author: Edward, Location: In the garagePosted: Sun Jun 19, 2011 1:41 am ---- All sounds very dangerous being so low that bumpstops have to be removed.
#13: Re: Cant go lower? Author: rttam, Location: devonPosted: Sun Jun 19, 2011 2:10 am ----
Edward wrote:
All sounds very dangerous being so low that bumpstops have to be removed.
im all for lowering your car but not when its going to make it unsafe to drive it!!!
#14: Re: Cant go lower? Author: nakednakeddave, Location: aberdeenPosted: Sun Jun 19, 2011 2:30 am ---- wont necesarily make it unsafe.... just not very comfortable to drive and all your suspension bushes with seperate n die alot faster haha
#15: Re: Cant go lower? Author: Edward, Location: In the garagePosted: Sun Jun 19, 2011 2:35 am ---- If it's bumpy it means is has no suspension. That is what keeps the tyres on the road.
We are not responsible for comments posted by our users, as they are the property of the poster
Interactive software released under GNU GPL,
Code Credits,
Privacy Policy
Membership:
Latest: 
New Today: 0
New Yesterday: 0
Overall: 17130
Online Now [585]:
Visitors: 584
Members: 0
Staff Online Now:
Page Views:
General
