New Here?
Toggle Content
   

Toggle Content User Info
Welcome

Anonymous

Nickname
Password
Register

Membership:
Latest: Puggingalong
New Today: 0
New Yesterday: 0
Overall: 17129

Online Now [278]:
Visitors: 277
Bots: 1
Members: 0
Staff Online Now:

No staff members are online!
Page Views:
Today: 32216
Total: 101454371

Toggle Content Main Menu
 General Info Goodies Search Web Stats Members
 Donations

 

Forums ›

:: Forums ›
wont tick over
Go to page Previous  1, 2, 3, 4, 5, 6, 7, 8  Next  :| |:
-> 206 Problems

#16: Re: wont tick over Author: dumdum0910, Location: letchworth PostPosted: Wed Nov 09, 2011 3:30 pm
    ----
ill ask about

#17: Re: wont tick over Author: dumdum0910, Location: letchworth PostPosted: Thu Nov 10, 2011 5:59 am
    ----
found out 1 of my mates has the same coil pack on his motor so tested that and it still ran like crap. so toke apart the throttle body and found it all full of crap. so just waiting for my old man to come back with some carb cleaner .

#18: Re: wont tick over Author: dumdum0910, Location: letchworth PostPosted: Thu Nov 10, 2011 7:10 am
    ----
cleaned the throttle body , map , icv , tps and still running bad . ive noticed when it does tick over the revs go up and down . could this be the tps ?

#19: Re: wont tick over Author: mattievrs, Location: Leicester PostPosted: Thu Nov 10, 2011 10:20 am
    ----
guess you'll be best off try a NEW ICV then if it doesnt sort it, id get it to a garage mate.

#20: Re: wont tick over Author: dumdum0910, Location: letchworth PostPosted: Thu Nov 10, 2011 10:43 am
    ----
after i gave it a run i plugged it in to the obd scanner and it came up idle control system so ordered 1 fingers crossed it fixes it

#21: Re: wont tick over Author: dumdum0910, Location: letchworth PostPosted: Fri Nov 11, 2011 1:18 pm
    ----
so got a new icv , fitted and made it even worse . revs went straight to 3000 rpm then down to 2000 and started bouncing between 2000 and 2500 :S so toke it off and sent it back as a faulty part, now waiting for another 1 to be delivered

#22: Re: wont tick over Author: Lee, Location: England PostPosted: Fri Nov 11, 2011 2:07 pm
    ----
48-62ohms between pins A and D
48-62ohms between pins B and C

#23: Re: wont tick over Author: dumdum0910, Location: letchworth PostPosted: Fri Nov 11, 2011 3:08 pm
    ----
which pins what? and is that while engine is running or with just ignition on

#24: Re: wont tick over Author: Lee, Location: England PostPosted: Fri Nov 11, 2011 3:18 pm
    ----
On the ICV when it's removed.

#25: Re: wont tick over Author: dumdum0910, Location: letchworth PostPosted: Fri Nov 11, 2011 3:35 pm
    ----
right so let me get this right. with the engine off remove the icv with it still connected and check the ohms between the pins ?

#26: Re: wont tick over Author: Lee, Location: England PostPosted: Fri Nov 11, 2011 5:16 pm
    ----
No.

Remove the ICV and check the ohms on the pins on the ICV

#27: Re: wont tick over Author: dumdum0910, Location: letchworth PostPosted: Fri Nov 11, 2011 5:27 pm
    ----
ok i will do that tomorrow and see what happens

#28: Re: wont tick over Author: dumdum0910, Location: letchworth PostPosted: Sat Nov 12, 2011 7:13 am
    ----
so checked the old icv pin A and D 47ohm , B and C 47 ohm and with the plunger pushed in A and D 46.8ohm and B and C 46.8 ohms. does this mean the icv is knackered or come the problem be else were?

#29: Re: wont tick over Author: dumdum0910, Location: letchworth PostPosted: Sun Nov 13, 2011 5:28 am
    ----
could some one advise me on what the temp sensor should be reading? ohms?

#30: Re: wont tick over Author: dumdum0910, Location: letchworth PostPosted: Mon Nov 14, 2011 12:57 pm
    ----
so replaced the icv again with another new replacment. it was fine for about a second then revs slowly went up to 3krpm Sad i gave it another ecu reset and bsi reset and no change so put in original icv. im now lost on what else it could be. much help appreciated, i have now noticed once its had a run and i leave the car ticking over it will idle normal but once i go to move again and stop at a junction it will run crap again.



-> 206 Problems


Go to page Previous  1, 2, 3, 4, 5, 6, 7, 8  Next  :| |:

Page 2 of 8
 
We are not responsible for comments posted by our users, as they are the property of the poster
Interactive software released under GNU GPL, Code Credits, Privacy Policy