#1: Antons HDI Author: anton1989, Location: west midlandsPosted: Fri Nov 16, 2012 4:25 pm ---- So here is my 2.0hdi. Nothing special, just wanted it looking like a 180, nothing o.t.t.
Car came in a sorry state!
This proves m.o.ts aint worth the paper there written on! Track rod ends and wishbones were down as an advisory!
Anyway. . . .
New lemforder track rod ends, wishbones, and all original peugeot water pump, cambelt kit, aux belt and a few other bits
On to the moding. . . .
Already had loads of parts from my old 206
Vortex
L.E.D Rear lights
DRL headlights
Full 180 interior
Heko deflectors
Sp bonnet vent
Black front pug badge
And few other parts
Also bought
Sp grill
180 carbon door surround, vent surrounds etc.
180 wing mirrors
Cupra r splitter and a
New fog light lol
Also painted calipers gold and de-badged rear
So car was looking like this
Then de-wipered and bought a ph 2 boot handle
Then ooops! Backed into a van on my way to see ash (member on here)
Not happy
Thats about it so far
I like that pic lol.
Future plans. . .
Get off my a**e and finish fmic
Fix dent
fit gti 6 brakes i have sitting in the shed
Fit my smoothed boot maybe?
Refurb alloys
Lower
Paint fogs
Fit the gti rear beam I have
And maybe a remap
Plan to sell in june so none of that may get done lol
Thanks for looking. Comments welcome good or bad.
#2: Re: Antons HDI Author: DanT, Location: Torbay, EnglandPosted: Fri Nov 16, 2012 4:38 pm ---- Looks smart buddy, a massive improvement! Shame about the dent
What you planning to replace it with?
#3: Re: Antons HDI Author: Andy_, Location: Isle of ManPosted: Fri Nov 16, 2012 4:39 pm ---- Really like what you've done so far
#4: Re: Antons HDI Author: P6RAF, Location: PlymouthPosted: Fri Nov 16, 2012 4:41 pm ---- Looking real nice, your hard work has payed off. Shame about the van though !
BTW is it easy to fit the Cupra splitter? They look like there's not much of a fitting surface, just lots of clips. How did you secure it to the bumper ?
Job well done, hats off
#5: Re: Antons HDI Author: anton1989, Location: west midlandsPosted: Fri Nov 16, 2012 4:43 pm ---- thanks, and not sure really really want a red 206 but this is my 3rd 206 now lol
#6: Re: Antons HDI Author: anton1989, Location: west midlandsPosted: Fri Nov 16, 2012 4:47 pm ----
perrygraf wrote:
Looking real nice, your hard work has payed off. Shame about the van though !
BTW is it easy to fit the Cupra splitter? They look like there's not much of a fitting surface, just lots of clips. How did you secure it to the bumper ?
Job well done, hats off
thanks, yeah the van was my fault splitter is easy to fit, i bought mine already cut to size from a member on here so all i had to do was screw it on with about 8 self tappers job done!
#7: Re: Antons HDI Author: P6RAF, Location: PlymouthPosted: Fri Nov 16, 2012 4:55 pm ---- OK thanks for the info.
Just got to find one at a reasonable price now !
#8: Re: Antons HDI Author: anton1989, Location: west midlandsPosted: Fri Nov 16, 2012 5:03 pm ----
perrygraf wrote:
OK thanks for the info.
Just got to find one at a reasonable price now !
they come up on ebay all the time. plp fit them on the mk4 r32 so your be lucky to get one under £35-£40
#9: Re: Antons HDI Author: P6RAF, Location: PlymouthPosted: Fri Nov 16, 2012 5:28 pm ---- That's the kinda prices I've seen. I'm only happy buying bargains !!
I'll keep on looking as they do look the part.
BTW, "already cut to size" What needed cutting ? Looking closely at yours I can't see any cuts/joins.
#10: Re: Antons HDI Author: anton1989, Location: west midlandsPosted: Fri Nov 16, 2012 6:02 pm ----
perrygraf wrote:
That's the kinda prices I've seen. I'm only happy buying bargains !!
I'll keep on looking as they do look the part.
BTW, "already cut to size" What needed cutting ? Looking closely at yours I can't see any cuts/joins.
good that you cant see its made to fit a cupra so is longer just needs triming abit
yh i wouldt of bought this if its was not so cheap and the seller was down the road from me too so no postage cost etc
#11: Re: Antons HDI Author: DeadEyePaul, Location: Rugby,WarwickshirePosted: Sat Nov 17, 2012 1:46 am ---- Looking good
#12: Re: Antons HDI Author: Edward, Location: In the garagePosted: Sat Nov 17, 2012 3:33 am ---- Are you putting the fan back?
#13: Re: Antons HDI Author: anton1989, Location: west midlandsPosted: Sat Nov 17, 2012 4:26 am ---- Thanks paul. And yes Edward, I will be fitting a slimline one to the back of the rad after christmas
#14: Re: Antons HDI Author: jimjam19927, Location: PortsmouthPosted: Sat Nov 17, 2012 4:33 am ---- confused is your avatar a photoshop of smooth boot then? I thought you got one in the end? Back your rear end like that is a massive pie i bet that hurt especially as you got it looking so good.
#15: Re: Antons HDI Author: anton1989, Location: west midlandsPosted: Sat Nov 17, 2012 4:55 am ---- yeah its a p/s mate i have the boot just not fitted it as i am in two minds really. yeah very gutted so much that i lost intrest in the car for ages!
#16: Re: Antons HDI Author: anton1989, Location: west midlandsPosted: Sun Dec 02, 2012 10:29 am ---- small update
got the fmic all piped up, just need to refit my fog lights! lol
#17: Re: Antons HDI Author: DeadEyePaul, Location: Rugby,WarwickshirePosted: Sun Dec 02, 2012 10:40 am ---- Niice 1
#18: Re: Antons HDI Author: anton1989, Location: west midlandsPosted: Sun Dec 02, 2012 11:24 am ----
DeadEyePaul wrote:
Niice 1
cheers mate
it was a pain in the a**e!
could do it again easy now though
#19: Re: Antons HDI Author: Mada, Location: Manchester/ AberdeenPosted: Mon Dec 03, 2012 4:30 pm ---- How much did in cost you in total to do the intercooler set up?
I really like your headlights too. Don't normally like that style, but really suits your car!
#20: Re: Antons HDI Author: ARRAN, Location: WiltshirePosted: Wed Dec 05, 2012 12:42 pm ---- Headlights suit it well, DRL lights normally look tacky but they look like they're made to be on the car! Good work.
#21: Re: Antons HDI Author: anton1989, Location: west midlandsPosted: Thu Dec 20, 2012 4:12 pm ----
ARRAN wrote:
Headlights suit it well, DRL lights normally look tacky but they look like they're made to be on the car! Good work.
cheers mate. they look good but output is poor just as the angels
cost me £150 for the i/c, the 2 parts you need to make it work and loads of pipe work. i bought it from a member on here. could of got it cheaper if i looked but wanted it there and then. also i used 2.5inch pipe i would not recommend using it 2inch would have been perfect and a hell of alot less hassle. cost another £25 for some more hoses i needed so £175 BUT i could do it all again if had to for no more than £100 easy.
#22: Re: Antons HDI Author: bri-man, Posted: Sat Dec 29, 2012 6:50 am ---- dude! do you think the guy who modded your splitter would do one for me? slide him a few quid for his troubles! or a guide on how to do it
#23: Re: Antons HDI Author: Uz, Location: No Man's LandPosted: Sat Dec 29, 2012 9:33 am ---- Bri, you can do it yourself all you need is a hack saw blade and a load of heavy duty self taping bolts which you can put a nut one once they've gone through. Takes about an hour to fit the splitter to the bumper including all the lining up and centralising etc.
Anton, cars coming along nicely dude... whats the deal behind selling all the 180 stuff..? change of plans etc..? sorry if you've already said... not read the whole thread just scanned through the images and the FMIC install.
#24: Re: Antons HDI Author: bri-man, Posted: Sun Dec 30, 2012 9:21 am ---- ahh cool! ill give it ago thanks
#25: Re: Antons HDI Author: 00budham00, Location: IpsPosted: Sun Dec 30, 2012 10:15 am ---- Looks cool from the front with the inter cooler
#26: Re: Antons HDI Author: anton1989, Location: west midlandsPosted: Mon Dec 31, 2012 4:30 am ----
Uz wrote:
Bri, you can do it yourself all you need is a hack saw blade and a load of heavy duty self taping bolts which you can put a nut one once they've gone through. Takes about an hour to fit the splitter to the bumper including all the lining up and centralising etc.
Anton, cars coming along nicely dude... whats the deal behind selling all the 180 stuff..? change of plans etc..? sorry if you've already said... not read the whole thread just scanned through the images and the FMIC install.
thanks mate. car is going back to standard now due to needing a 5 door. so i will be selling the car soon. sold most parts now. some lucky member got my 180 interior, drl headlights, cupra splitter and rear lights for £340
#27: Re: Antons HDI Author: anton1989, Location: west midlandsPosted: Mon Dec 31, 2012 4:32 am ----
00budham00 wrote:
Looks cool from the front with the inter cooler
yh i think it looks kinda mean not over the top, got the look i was going for just needed lowering, wheel refurb and i was done on the looks side of it
#28: Re: Antons HDI Author: 00budham00, Location: IpsPosted: Mon Dec 31, 2012 5:37 am ----
anton1989 wrote:
00budham00 wrote:
Looks cool from the front with the inter cooler
yh i think it looks kinda mean not over the top, got the look i was going for just needed lowering, wheel refurb and i was done on the looks side of it
what did it cost you to fit all n all ?
#29: Re: Antons HDI Author: anton1989, Location: west midlandsPosted: Mon Dec 31, 2012 5:54 am ---- What did what cost mate
#30: Re: Antons HDI Author: bri-man, Posted: Mon Dec 31, 2012 6:22 am ---- If your selling mate would you sell the Intercooler?
#31: Re: Antons HDI Author: anton1989, Location: west midlandsPosted: Mon Dec 31, 2012 9:24 am ---- Had a few plp ask for it. Not sure yet will put it up in for sale thread if I do mate
#32: Re: Antons HDI Author: anton1989, Location: west midlandsPosted: Sat Mar 23, 2013 10:35 am ---- car is now for sale
We are not responsible for comments posted by our users, as they are the property of the poster
Interactive software released under GNU GPL,
Code Credits,
Privacy Policy
Membership:
Latest: 
New Today: 0
New Yesterday: 0
Overall: 17130
Online Now [254]:
Visitors: 253
Members: 0
Staff Online Now:
Page Views:
General
really want a red 206 but this is my 3rd 206 now lol
splitter is easy to fit, i bought mine already cut to size from a member on here so all i had to do was screw it on with about 8 self tappers job done!
its made to fit a cupra so is longer just needs triming abit
