#1: New Clutch, Sleeve & Cable Replaced... PROBLEMS Author: GlennMRX, Posted: Wed May 07, 2014 5:34 am ---- Hello,
I replaced the Clutch in my XS recently, Luk Clutch fitted, Genuine Clutch Cable fitted and replaced the sleeve/seal aswell, but the biting point is so high up the pedal, its about 10mm from the end of the pedal.
I have adjusted the pedal, it is now higher than the brake pedal, i cant lower the clutch pedal anymore or the clutch will slip?
Anyone any advice on how to put this right?? I am scared the clutch will soon start to slip and I dont want to ruin my new clutch
Thanks
Glenn.
#2: Re: New Clutch, Sleeve & Cable Replaced... PROBLEMS Author: DREWDEN, Location: huddersfieldPosted: Wed May 07, 2014 6:21 am ----
GlennMRX wrote:
Hello,
I replaced the Clutch in my XS recently, Luk Clutch fitted, Genuine Clutch Cable fitted and replaced the sleeve/seal aswell, but the biting point is so high up the pedal, its about 10mm from the end of the pedal.
I have adjusted the pedal, it is now higher than the brake pedal, i cant lower the clutch pedal anymore or the clutch will slip?
Anyone any advice on how to put this right?? I am scared the clutch will soon start to slip and I dont want to ruin my new clutch
#3: Re: New Clutch, Sleeve & Cable Replaced... PROBLEMS Author: GlennMRX, Posted: Wed May 07, 2014 6:42 am ----
DREWDEN wrote:
GlennMRX wrote:
Hello,
I replaced the Clutch in my XS recently, Luk Clutch fitted, Genuine Clutch Cable fitted and replaced the sleeve/seal aswell, but the biting point is so high up the pedal, its about 10mm from the end of the pedal.
I have adjusted the pedal, it is now higher than the brake pedal, i cant lower the clutch pedal anymore or the clutch will slip?
Anyone any advice on how to put this right?? I am scared the clutch will soon start to slip and I dont want to ruin my new clutch
thanks for that DREWDEN, I must go check if i can pull the cable out of the clutch lever at the gearbox, I must say when fitting the cable it was seriously tight to the point where we had to use a prybar to move the clutch lever back to get the cable in place! I even followed a Peugeot bulletin on how to fit the cable!
#4: Re: New Clutch, Sleeve & Cable Replaced... PROBLEMS Author: kandlbarrett, Location: SwindonPosted: Thu May 08, 2014 5:40 pm ---- Sounds like the cable has auto adjusted before fully fitting.
#5: Re: New Clutch, Sleeve & Cable Replaced... PROBLEMS Author: kandlbarrett, Location: SwindonPosted: Fri May 09, 2014 6:47 am ---- Or the cable is not correctky located on the pedal - it is fun getting that end on isn't it!
#6: Re: New Clutch, Sleeve & Cable Replaced... PROBLEMS Author: GlennMRX, Posted: Fri May 09, 2014 8:09 am ---- yeah my hand was cut to bits! Its located on the pedal ok... argh, gonna have to fork out for another cable! why couldnt they make it with a piece of threaded bar on the end and a wee adjuster nut? Had to try and be smart and make it awkward!
#7: Re: New Clutch, Sleeve & Cable Replaced... PROBLEMS Author: MrBSI, Location: What's it to you? ? ?Posted: Fri May 09, 2014 12:26 pm ----
GlennMRX wrote:
why couldnt they make it with a piece of threaded bar on the end and a wee adjuster nut? Had to try and be smart and make it awkward!
Because the auto adjusting cable has worked perfectly fine for many years on plenty of other PSA products.
It does the job perfectly, fit it correctly first time & then forget about it.
We are not responsible for comments posted by our users, as they are the property of the poster
Interactive software released under GNU GPL,
Code Credits,
Privacy Policy
Membership:
Latest: 
New Today: 0
New Yesterday: 0
Overall: 17129
Online Now [171]:
Visitors: 170
Members: 0
Staff Online Now:
Page Views:
General
