#1: Pp2000 issue Author: MrWhite, Posted: Sun Jun 01, 2014 2:26 pm ---- I am looking for a little bit of advice after purchasing a second hand peugeot planet cable with software. I have installed it and activated it successfully on a fresh installed XP laptop, but there is no reply from the ecu on a global test and nothing else will respond when testing individually. I am almost certain there is a fault with the lead but has anyone else had a similar issue or know how to remedy it?
If I have missed any info out please inform me so I can update
51 plate 206 2.0 hdi is what I was plugging it into
#2: Re: Pp2000 issue Author: MrBSI, Location: What's it to you? ? ?Posted: Sun Jun 01, 2014 2:35 pm ---- I take it the green light is glowing on the interface?
Drivers installed correctly for the interface?
Turned the USB power saving setting OFF in device manager on your XP machine?
#3: Re: Pp2000 issue Author: MrWhite, Posted: Sun Jun 01, 2014 3:48 pm ---- Yeah I checked all three before posting I am not sure what else to try except plugging into another car perhaps.
#4: Re: Pp2000 issue Author: Steve206, Location: UKPosted: Sun Jun 01, 2014 4:51 pm ---- I'd try another car, Peugeot planet wont usually start unless it detects the cable.
Also check the pins on the cable and the obd port.
#5: Re: Pp2000 issue Author: MrWhite, Posted: Mon Jun 02, 2014 3:22 pm ---- Ok the pins seem fine no damage or missing pins etc, I just need a willing victim * ahem* volunteer for me to plug their car into.
Ok the pins seem fine no damage or missing pins etc, I just need a willing victim * ahem* volunteer for me to plug their car into.
That would probably depend on where you are.
#7: Re: Pp2000 issue Author: qwert, Location: ukPosted: Tue Jun 03, 2014 12:48 pm ---- Why not just test the +12v and earth on your obd port.
#8: Re: Pp2000 issue Author: heyziq, Location: MalaysiaPosted: Wed Jun 04, 2014 3:28 am ---- is the driver cable detected or had been installed
at 1st place?
#9: Re: Pp2000 issue Author: sean.r.steward, Location: norfolkPosted: Wed Jun 04, 2014 6:53 pm ---- What you need my frend is a snap-on machine. Because they work lmao
#10: Re: Pp2000 issue Author: MrBSI, Location: What's it to you? ? ?Posted: Thu Jun 05, 2014 11:48 am ----
sean.r.steward wrote:
What you need my frend is a snap-on machine. Because they work lmao
Ill stick with Planet / Lexia or as it's known now Diagbox as it's much better & has a hell of a lot more features available for PSA products then anything Snap On could wish for
Diagbox V7.44 does me fine
[img]
[/img]
#11: Re: Pp2000 issue Author: MrBSI, Location: What's it to you? ? ?Posted: Thu Jun 05, 2014 11:59 am ----
MrWhite wrote:
I am looking for a little bit of advice after purchasing a second hand peugeot planet cable with software. I have installed it and activated it successfully on a fresh installed XP laptop, but there is no reply from the ecu on a global test and nothing else will respond when testing individually. I am almost certain there is a fault with the lead but has anyone else had a similar issue or know how to remedy it?
If I have missed any info out please inform me so I can update
51 plate 206 2.0 hdi is what I was plugging it into
Have a look at the pins inside the big round connector, a few people have reported these give issues in the past.
Also have you opened up the interface & checked the soldering on to the board where the wires / connector is attached?
#12: Re: Pp2000 issue Author: MrWhite, Posted: Sun Jun 08, 2014 3:06 pm ---- hey guys sorry I havent been back on for a few days (Spent the weekend in the lakes)
Qwert please can you elaborate a bit on what to do there, Sorry I am not sure what to look at
heyziq Yeah I followed the instructions to the letter and the Drivers for the interface are correctly installed and recognizes when plugged into the USB ports
MrBSI I did look at the pins in the round connector and all seems well.. also i did open up the interface and the solders seem fine unless there's something even smaller I haven't spotted?
Is there any member Near me in Padiham I could perhaps meet and try to fix over a few drinks? (I am prepared to travel as I'm sure there isn't anyone within 30 miles)
#13: Re: Pp2000 issue Author: macca1411, Location: Westhoughton, LancashirePosted: Sun Jun 08, 2014 3:14 pm ----
MrWhite wrote:
Is there any member Near me in Padiham I could perhaps meet and try to fix over a few drinks? (I am prepared to travel as I'm sure there isn't anyone within 30 miles)
I'm 33.5 miles via M65/M61, even closer through Abbey Village and over the tops. Could be a couple of weeks before I'm free though.
#14: Re: Pp2000 issue Author: qwert, Location: ukPosted: Mon Jun 09, 2014 2:59 pm ---- Get a multimeter to check there is power going to the OBD port on the car
#15: Re: Pp2000 issue Author: MrWhite, Posted: Tue Jun 10, 2014 4:14 pm ---- oh on the car.. Right yes there is as it was plugged in to a different machine a few months ago I cannot get access to the other machine again but it was fine on the car end.
Macca just pm me when you do get any free time I will have to wait. If its faulty i may sell it and buy another and just deal with my loss'
We are not responsible for comments posted by our users, as they are the property of the poster
Interactive software released under GNU GPL,
Code Credits,
Privacy Policy
Membership:
Latest: 
New Today: 0
New Yesterday: 0
Overall: 17129
Online Now [116]:
Visitors: 115
Members: 0
Staff Online Now:
Page Views:
General
