#1: May have found the cure for the leak on my 180 Author: mattymj, Location: NorfolkPosted: Thu Apr 02, 2015 3:50 pm ---- This washer goes between the oil cooler, further up.
I wonder if I replace it if it needs to be torqued up?
Thanks
#2: Re: May have found the cure for the leak on my 180 Author: Timon2210, Location: PalestinePosted: Fri Apr 03, 2015 3:42 am ---- Well done
#3: Re: May have found the cure for the leak on my 180 Author: gpvecchi, Location: ItalyPosted: Fri Apr 03, 2015 2:29 pm ---- Nevermind, I tried all the things, I changed 3 gaskets, I torqued it up, down, no way. After a week the oil leak comes back.
#4: Re: May have found the cure for the leak on my 180 Author: ukskater01, Location: sutton surrey/welwyn garden cityPosted: Fri Apr 03, 2015 3:58 pm ---- Wash the oil off with a jet wash and then recheck after a drive to see where it's coming from
#5: Re: May have found the cure for the leak on my 180 Author: mattymj, Location: NorfolkPosted: Tue Apr 07, 2015 6:01 pm ---- Shall hopefully be getting my new washer Thursday. When refitting is the a torque setting for the big bolt that screws through the oil cooler?
#6: Re: May have found the cure for the leak on my 180 Author: oldskoolz, Location: LondonPosted: Wed Apr 08, 2015 7:11 am ----
mattymj wrote:
Shall hopefully be getting my new washer Thursday. When refitting is the a torque setting for the big bolt that screws through the oil cooler?
I would imagine there is considering there is a gasket behind it. Try it as hand tight plus a quarter turn and see from there, most rubber seals will be crushed beyond this point.
#7: Re: May have found the cure for the leak on my 180 Author: Steve206, Location: UKPosted: Wed Apr 08, 2015 1:23 pm ---- Would it hurt to put sump sealant on the outer edges?
#8: Re: May have found the cure for the leak on my 180 Author: mattymj, Location: NorfolkPosted: Thu Apr 09, 2015 8:38 am ---- I have the new seal. Peugeot state a 8 nm tightening! Isn't that hand tight?
#9: Re: May have found the cure for the leak on my 180 Author: oldskoolz, Location: LondonPosted: Thu Apr 09, 2015 8:48 am ----
mattymj wrote:
I have the new seal. Peugeot state a 8 nm tightening! Isn't that hand tight?
Without a torque wrench its hard to say
#10: Re: May have found the cure for the leak on my 180 Author: mattymj, Location: NorfolkPosted: Thu Apr 09, 2015 8:57 am ---- Could go for hand tight plus a 1/4 turn!
#11: Re: May have found the cure for the leak on my 180 Author: mattymj, Location: NorfolkPosted: Thu Apr 09, 2015 10:38 am ---- Not too much difference
#12: Re: May have found the cure for the leak on my 180 Author: mattymj, Location: NorfolkPosted: Thu Apr 09, 2015 12:13 pm ---- I found the cooler had lines on it so I hand tightened it then aligned it square
#13: Re: May have found the cure for the leak on my 180 Author: Project2062014, Location: CornwallPosted: Fri Apr 10, 2015 9:02 am ----
Steve206 wrote:
Would it hurt to put sump sealant on the outer edges?
Shoot me
#14: Re: May have found the cure for the leak on my 180 Author: Steve206, Location: UKPosted: Fri Apr 10, 2015 9:25 am ---- ?
#15: Re: May have found the cure for the leak on my 180 Author: Leegsi, Location: Near PortsmouthPosted: Fri Apr 10, 2015 2:15 pm ---- So did it sort your leak?
We are not responsible for comments posted by our users, as they are the property of the poster
Interactive software released under GNU GPL,
Code Credits,
Privacy Policy
Membership:
Latest: 
New Today: 0
New Yesterday: 0
Overall: 17130
Online Now [45]:
Visitors: 44
Members: 0
Staff Online Now:
Page Views:
General
