|
Author
|
Message |
|
|
 Posted: Thu Feb 10, 2011 3:06 am |
|
|
|
|
Joined: Feb 08, 2010
Posts: 6055
Trade Rating: +53
Location: Salisbury / New Forest
|
 |
| Edward wrote: |
Just unplug the idle control valve! Have you tested the fuel pressure?
Oily inlets are normal because the engine vents into the inlet. No point in cleaning it as it will just oil up again. |
Thats a good shout.
The fuel pump does sound a bit weak.
I'll see if I can test it this weekend.
| |  |
|
|
 |
|
|
|
|
|
|
Posted: Thu Feb 10, 2011 3:13 am |
|
|
|
|
Joined: Feb 07, 2010
Posts: 1792
Trade Rating: +12
Location: Bridgnorth, Nr Wolverhampton
|
|
|
|
|
|
|
|
|
|
|
Posted: Thu Feb 10, 2011 7:29 am |
|
|
|
|
Joined: Feb 08, 2010
Posts: 6055
Trade Rating: +53
Location: Salisbury / New Forest
|
|
Scanned it for faul codes got:
P0170 - Fuel Trim malfunction (Bank 1)
P0135 - 02 Sensor Heater Circuit Malfunction (Bank 1 Sensor 1)
P0116 - Engine coolant Temp CKT Range/Performance
P0170P - ?
P0135P - ?
P0116P - ?
P0131P - 02 Sensor Circuit Low Volts (Bank 1 Sensor 1)
I'm not sure what the ones with the P at the end mean?
So what's the next step?
| | |
|
|
|
|
|
|
|
|
|
|
Posted: Thu Feb 10, 2011 7:34 am |
|
|
|
|
Joined: Feb 07, 2010
Posts: 1792
Trade Rating: +12
Location: Bridgnorth, Nr Wolverhampton
|
|
looks like you need a new lambda id say, atleast thats a couple of codes out the way
| | |
|
|
|
|
|
|
|
|
|
|
Posted: Thu Feb 10, 2011 7:50 am |
|
|
|
|
Joined: Feb 08, 2010
Posts: 6055
Trade Rating: +53
Location: Salisbury / New Forest
|
|
What about the 1st & 3rd code?
| | |
|
|
|
|
|
|
|
|
|
|
Posted: Thu Feb 10, 2011 8:25 am |
|
|
|
|
Joined: Aug 01, 2010
Posts: 1741
Trade Rating: +7
Location: Peterborough
|
|
Did you say you replaced the Temp Sensor? What about the thermostat?
| | |
|
|
|
|
 | |  |
| Peugeot 206 1.4LX - Sold
Peugeot 206 2.0HDI D-Turbo - Dead
Vokswagen Bora 2.0 - Sold
Seat Leon MK2 2.0 TDI - New
| |
 | |  |
|
|
|
|
|
|
|
Posted: Thu Feb 10, 2011 8:36 am |
|
|
|
|
Joined: Feb 08, 2010
Posts: 6055
Trade Rating: +53
Location: Salisbury / New Forest
|
|
Where is the thermostat located?
| | |
|
|
|
|
|
|
|
|
|
|
Posted: Thu Feb 10, 2011 8:40 am |
|
|
|
|
Joined: Feb 08, 2010
Posts: 7045
Trade Rating: +5
Location: In the garage
|
|
Dodgy thermostat wouldn't cause a fault code to pop up. If it was open the engine just wouldn't warm up so it would be in warm up mode all the time.
| | |
|
|
|
|
| | |
| 2001 GTi 138, Bilstein Sprint dampers, H&R springs, 21mm Peugeot Sport torsion bars, 22mm rear ARB, Peugeot Sport Group A wishbones, 283mm discs, Goodridge stainless hoses, Maniflow 304 grade 4-2-1 2.5" manifold and system, 200 cell cat, Richard Longman head, 45mm Jenvey throttle bodies, 9.5mm TB spacers, 90mm air horns, Jenvey throttle linkage, Jenvey fuel rail, Aeromotive and Goodridge fuel fittings and braided hose, ITG sausage filter, Radtec custom radiator, Piper Ultimate Road cams, Piper vernier pulleys, Omex 600 ECU. Saxo electric PAS pump, Vibra Technics engine mounts. Samco coolant hoses, TTV steel flywheel, 4.76 final drive ratio, 307 CC 180 ratios. 2019 BMW 530i. 2017 Mercedes C300 convertible. | |
| | |
|
|
|
|
|
|
|
Posted: Thu Feb 10, 2011 8:49 am |
|
|
|
|
Joined: Feb 08, 2010
Posts: 6055
Trade Rating: +53
Location: Salisbury / New Forest
|
|
| Edward wrote: |
| Dodgy thermostat wouldn't cause a fault code to pop up. If it was open the engine just wouldn't warm up so it would be in warm up mode all the time. |
What do you think the first one is?
Something to do with the fuel pump?
| | |
|
|
|
|
|
|
|
|
|
|
Posted: Thu Feb 10, 2011 9:17 am |
|
|
|
|
Joined: Feb 07, 2010
Posts: 13077
Trade Rating: +65
Location: England
|
|
Found out for you
The second P in the codes mean they are Pending.
Pending codes are soft codes, they are like a "heads up, something might be wrong" warning.
| | |
|
|
|
|
|
|
|
|
|
|
Posted: Thu Feb 10, 2011 9:20 am |
|
|
|
|
Joined: Feb 08, 2010
Posts: 6055
Trade Rating: +53
Location: Salisbury / New Forest
|
|
| Lee wrote: |
Found out for you
The second P in the codes mean they are Pending.
Pending codes are soft codes, they are like a "heads up, something might be wrong" warning. |
So clearing them should sort it?
(And changing the 02 sensor)
What is "P0170 - Fuel Trim malfunction (Bank 1)" though?
| | |
|
|
|
|
|
|
|
|
|
|
Posted: Thu Feb 10, 2011 10:35 am |
|
|
|
|
Joined: Feb 07, 2010
Posts: 13077
Trade Rating: +65
Location: England
|
|
Will be something to do with the mixture of the fuel/air, so if you have changed the lambda sensor it could have been taht at fault.
| | |
|
|
|
|
|
|
|
|
|
|
Posted: Thu Feb 10, 2011 10:42 am |
|
|
|
|
Joined: Feb 08, 2010
Posts: 6055
Trade Rating: +53
Location: Salisbury / New Forest
|
|
| Lee wrote: |
| Will be something to do with the mixture of the fuel/air, so if you have changed the lambda sensor it could have been taht at fault. |
Just done some Googling
| Quote:: |
| Any injection fault that affects the expected amount of fuel used will set a fuel trim code. It literally means that the Lambda probe [exhaust oxygen sensor] is asking for more fuelling adjustment than the ECU has the capacity to alter the pre-set programming. [I.e. It's ability to "trim" the settings.] |
I'll change the sensor this evening. Hopefully thats the end of it & I can sell the car!
| | |
|
|
|
|
|
|
|
|
|
|
Posted: Fri Feb 11, 2011 3:00 am |
|
|
|
|
Joined: Feb 07, 2010
Posts: 1792
Trade Rating: +12
Location: Bridgnorth, Nr Wolverhampton
|
|
put mine back on last night, doesnt really seem to have sorted the problem, i put it back with new seals and stuff so that means that its not an air leak..
does feel a bit smoother but thats probably because i cleared out all the crap.
what code reader was it that you bought chris??
| | |
|
|
|
|
|
|
|
|
|
|
Posted: Fri Feb 11, 2011 3:05 am |
|
|
|
|
Joined: Feb 08, 2010
Posts: 6055
Trade Rating: +53
Location: Salisbury / New Forest
|
|
I'm just borrowing it.
It's an OBDII scanner, I'm pretty sure it's this: cgi.ebay.co.uk/U480-OB...2a050e464e
I tried changing the lambda sensor but its seized, letting it soak in WD40 and I'll have another go this weekend.
| | |
|
|
|
|
|
|
|
|
Membership:
Latest: 
New Today: 0
New Yesterday: 0
Overall: 17128
Online Now [44]:
Visitors: 43
Members: 0
Staff Online Now:
Page Views:
General
Forums Home
Forum FAQ
Search
