|
Author
|
Message |
|
|
 Posted: Sun May 15, 2011 2:49 pm |
|
|
|
|
Joined: Sep 11, 2010
Posts: 79
Trade Rating: 0
Location: Nottingham
|
 |
shine a torch in to the header tank and u will b able to see the level clearer
| |  |
|
|
 |
 | |  |
| drive fast !!! live life faster !!! | |
 | |  |
|
|
|
|
|
|
|
Posted: Sun May 15, 2011 2:58 pm |
|
|
|
|
Joined: Feb 08, 2010
Posts: 1407
Trade Rating: +1
Location: Berkshire
|
|
Cartoonhead the other screw i think is at bottom mid near radiator on and by thermastat its not in exact place as urs is it because mines a 2000 i actaully havent got bleed screw in same place heater matrix yeah but other is different place .Or i only have one bleed screw ? looks like one at end of thermastat mid in middle of radiator not right habd side like in your pic .
I just tries that still cant see level atall and its a bright good torch , this coolant bottles are s**t why they make it so hard meant to be easy checking coolant level . there's gotta be a easy way surely and the joke is if you fill it so you can see it thats a fair bit over max .
Would it hurt it much being bit over the max level ?
And its 50/50 water, coolant rite ?
| | |
|
|
|
|
| | |
| New car 2011 / Thoruim grey , 207 1.4 Vti 16v Sport 95bhp , tinted rear windows.
Old car 2000/ 206 2.0 hdi. | |
| | |
|
|
|
|
|
|
|
Posted: Sun May 15, 2011 3:04 pm |
|
|
|
|
Joined: Sep 11, 2010
Posts: 79
Trade Rating: 0
Location: Nottingham
|
|
it should just spew any excess coolant out
yeh most coolants 50/50
| | |
|
|
|
|
| | |
| drive fast !!! live life faster !!! | |
| | |
|
|
|
|
|
|
|
Posted: Sun May 15, 2011 3:05 pm |
|
|
|
|
Joined: Feb 08, 2010
Posts: 1407
Trade Rating: +1
Location: Berkshire
|
|
ok thanks
so should be fine to put bit more in over max ? ,
so i can at least see it better than none in there suppose because its the only way i can see if there's any in there .
| | |
|
|
|
|
| | |
| New car 2011 / Thoruim grey , 207 1.4 Vti 16v Sport 95bhp , tinted rear windows.
Old car 2000/ 206 2.0 hdi. | |
| | |
|
|
|
|
|
|
|
Posted: Sun May 15, 2011 3:09 pm |
|
|
|
|
Joined: Sep 11, 2010
Posts: 79
Trade Rating: 0
Location: Nottingham
|
|
yeh wont kill it if there's too much in it it should spew it out of an overflow and get its own level.
| | |
|
|
|
|
| | |
| drive fast !!! live life faster !!! | |
| | |
|
|
|
|
|
|
|
Posted: Sun May 15, 2011 3:09 pm |
|
|
|
|
Joined: Feb 08, 2010
Posts: 1407
Trade Rating: +1
Location: Berkshire
|
|
ok cheers
| | |
|
|
|
|
| | |
| New car 2011 / Thoruim grey , 207 1.4 Vti 16v Sport 95bhp , tinted rear windows.
Old car 2000/ 206 2.0 hdi. | |
| | |
|
|
|
|
|
|
|
Posted: Mon May 16, 2011 12:54 am |
|
|
|
|
Joined: Feb 08, 2010
Posts: 1407
Trade Rating: +1
Location: Berkshire
|
|
Think its sorted i did the other one tiny bit tight it back up,
topped up coolant and think its done the trick seems ok now ,
not making noise after 2 quick trips in my car for a test run .
| | |
|
|
|
|
| | |
| New car 2011 / Thoruim grey , 207 1.4 Vti 16v Sport 95bhp , tinted rear windows.
Old car 2000/ 206 2.0 hdi. | |
| | |
|
|
|
|
|
|
|
Posted: Mon May 16, 2011 3:27 am |
|
|
|
|
Joined: Feb 07, 2010
Posts: 2248
Trade Rating: +18
Location: Leicester
|
|
Id buy a new coolant tank lid mate. Sounds like the seal has gone in it. The caps are also self bleeding so you shouldnt have air in the system.
| | |
|
|
|
|
| | |
| NO LONGER ACTIVE ON THE FORUM | |
| | |
|
|
|
|
|
|
|
Posted: Mon May 16, 2011 5:39 am |
|
|
|
|
Joined: Feb 08, 2010
Posts: 1407
Trade Rating: +1
Location: Berkshire
|
|
ok , i ordered one last nite cause there only bout £6 .
Hate the way you just cant see in the damn coolant tank it must be the most stupid thing about the 206 lol .
| | |
|
|
|
|
| | |
| New car 2011 / Thoruim grey , 207 1.4 Vti 16v Sport 95bhp , tinted rear windows.
Old car 2000/ 206 2.0 hdi. | |
| | |
|
|
|
|
|
|
|
Posted: Mon May 16, 2011 5:54 am |
|
|
|
|
Joined: Feb 08, 2010
Posts: 7045
Trade Rating: +5
Location: In the garage
|
|
| mattievrs wrote: |
| Id buy a new coolant tank lid mate. Sounds like the seal has gone in it. The caps are also self bleeding so you shouldnt have air in the system. |
The system isn't self bleeding, that's why it has bleed screws fitted.
| | |
|
|
|
|
| | |
| 2001 GTi 138, Bilstein Sprint dampers, H&R springs, 21mm Peugeot Sport torsion bars, 22mm rear ARB, Peugeot Sport Group A wishbones, 283mm discs, Goodridge stainless hoses, Maniflow 304 grade 4-2-1 2.5" manifold and system, 200 cell cat, Richard Longman head, 45mm Jenvey throttle bodies, 9.5mm TB spacers, 90mm air horns, Jenvey throttle linkage, Jenvey fuel rail, Aeromotive and Goodridge fuel fittings and braided hose, ITG sausage filter, Radtec custom radiator, Piper Ultimate Road cams, Piper vernier pulleys, Omex 600 ECU. Saxo electric PAS pump, Vibra Technics engine mounts. Samco coolant hoses, TTV steel flywheel, 4.76 final drive ratio, 307 CC 180 ratios. 2019 BMW 530i. 2017 Mercedes C300 convertible. | |
| | |
|
|
|
|
|
|
|
Posted: Tue May 17, 2011 1:44 pm |
|
|
|
|
Joined: Feb 08, 2010
Posts: 1407
Trade Rating: +1
Location: Berkshire
|
|
also got new coolant lid def needed new one,
because new one feels so much more tight and better can feel the 15 psi if you get what i mean before was just a bit tight .
| | |
|
|
|
|
| | |
| New car 2011 / Thoruim grey , 207 1.4 Vti 16v Sport 95bhp , tinted rear windows.
Old car 2000/ 206 2.0 hdi. | |
| | |
|
|
|
|
|
Membership:
Latest: 
New Today: 0
New Yesterday: 0
Overall: 17126
Online Now [72]:
Visitors: 71
Members: 0
Staff Online Now:
Page Views:
General
Forums Home
Forum FAQ
Search
