|
Author
|
Message |
|
|
 Posted: Wed Nov 09, 2011 1:32 pm |
|
|
|
|
Joined: Apr 09, 2011
Posts: 445
Trade Rating: +1
Location: letchworth
|
 |
i have noticed every time i go to start my 206 it will stall striaght away , i have to put my foot on the throttle pedal to start , and also it stalls every time i change gear , what could be causing this problem . its had a ecu reset and no change. its a 1.1 2003
| |  |
|
|
 |
 | |  |
| if it dont scuff the ruff it aint low enuf | |
 | |  |
|
|
|
|
|
|
|
Posted: Wed Nov 09, 2011 1:33 pm |
|
|
|
|
Joined: Feb 08, 2010
Posts: 10151
Trade Rating: +12
|
|
ICV
| | |
|
|
|
|
|
|
|
|
|
|
Posted: Wed Nov 09, 2011 2:27 pm |
|
|
|
|
Joined: Apr 09, 2011
Posts: 445
Trade Rating: +1
Location: letchworth
|
|
i thort that may be the problem i did try and unplug it and plug it in while it was running and didnt make any diffrence , it will only tick over at 450rpm , ive adjusted the throttle for the time being until i get 5 mins to take it out and give it a clean
| | |
|
|
|
|
| | |
| if it dont scuff the ruff it aint low enuf | |
| | |
|
|
|
|
|
|
|
Posted: Wed Nov 09, 2011 2:51 pm |
|
|
|
|
Joined: Feb 07, 2010
Posts: 2248
Trade Rating: +18
Location: Leicester
|
|
ICV or TPS
| | |
|
|
|
|
| | |
| NO LONGER ACTIVE ON THE FORUM | |
| | |
|
|
|
|
|
|
|
Posted: Wed Nov 09, 2011 3:20 pm |
|
|
|
|
Joined: Apr 09, 2011
Posts: 445
Trade Rating: +1
Location: letchworth
|
|
toke the icv out gave it a clean and replaced oring. still no change , i pushed the plunger all the way in thinking the engine will rev when first started but it didnt :S is there any way of testing the throttle position sensor? i no when i have my obd scanner plugged in it does read the position throttle ok.
| | |
|
|
|
|
| | |
| if it dont scuff the ruff it aint low enuf | |
| | |
|
|
|
|
|
|
|
Posted: Wed Nov 09, 2011 3:57 pm |
|
|
|
|
Joined: Feb 07, 2010
Posts: 2248
Trade Rating: +18
Location: Leicester
|
|
Think the tps is part of the throttle housing. Whats the condition of the throttle housing ie clean/dirty? Have you cleaned the map sensor aswell?
| | |
|
|
|
|
| | |
| NO LONGER ACTIVE ON THE FORUM | |
| | |
|
|
|
|
|
|
|
Posted: Wed Nov 09, 2011 3:58 pm |
|
|
|
|
Joined: Apr 09, 2011
Posts: 445
Trade Rating: +1
Location: letchworth
|
|
the throttle housing is in good condition , ive never cleaned the map sensor . how do you do that?
| | |
|
|
|
|
| | |
| if it dont scuff the ruff it aint low enuf | |
| | |
|
|
|
|
|
|
|
Posted: Wed Nov 09, 2011 4:01 pm |
|
|
|
|
Joined: Apr 09, 2011
Posts: 445
Trade Rating: +1
Location: letchworth
|
|
when i toke the icv out there was some gunge around the plundger but not anything to worry about
| | |
|
|
|
|
| | |
| if it dont scuff the ruff it aint low enuf | |
| | |
|
|
|
|
|
|
|
Posted: Wed Nov 09, 2011 4:03 pm |
|
|
|
|
Joined: Feb 07, 2010
Posts: 2248
Trade Rating: +18
Location: Leicester
|
|
guessing its an 8v? its on the left hand front of the inlet with wires going into it. It should have a couple of screws in it.
| | |
|
|
|
|
| | |
| NO LONGER ACTIVE ON THE FORUM | |
| | |
|
|
|
|
|
|
|
Posted: Wed Nov 09, 2011 4:13 pm |
|
|
|
|
Joined: Apr 09, 2011
Posts: 445
Trade Rating: +1
Location: letchworth
|
|
yep i no were it is. i just toke it out it did have a bit of oil on it so blew what i could and cleaned as best as possible and still running low idle :S were the ecu has been reset so many times it wouldnt of lost its memory on were to tick over? just a possibilty
| | |
|
|
|
|
| | |
| if it dont scuff the ruff it aint low enuf | |
| | |
|
|
|
|
|
|
|
Posted: Wed Nov 09, 2011 4:17 pm |
|
|
|
|
Joined: Feb 07, 2010
Posts: 2248
Trade Rating: +18
Location: Leicester
|
|
| dumdum0910 wrote: |
| yep i no were it is. i just toke it out it did have a bit of oil on it so blew what i could and cleaned as best as possible and still running low idle :S were the ecu has been reset so many times it wouldnt of lost its memory on were to tick over? just a possibilty |
Clean everything with carb cleaner mate, not anything like wd40 as its oil based. Doesnt matter how many times you reset the ecu as its written on a chip to put it crudely.
Have you had the plugs out to see what condition theyre in?
| | |
|
|
|
|
| | |
| NO LONGER ACTIVE ON THE FORUM | |
| | |
|
|
|
|
|
|
|
Posted: Wed Nov 09, 2011 4:21 pm |
|
|
|
|
Joined: Apr 09, 2011
Posts: 445
Trade Rating: +1
Location: letchworth
|
|
the plugs r only a month old as i fitted bosch super 4s but i will check tomorrow , i will clean the map , icv and tps and plugs and see what happens.
just want to add its only started playing up since i filled up with petrol from some were else as i normally go to shell but went to asda this time 
| | |
|
|
|
|
| | |
| if it dont scuff the ruff it aint low enuf | |
| | |
Last edited by dumdum0910 on Wed Nov 09, 2011 4:22 pm; edited 1 time in total
|
|
|
|
|
|
|
Posted: Wed Nov 09, 2011 4:22 pm |
|
|
|
|
Joined: Feb 07, 2010
Posts: 2248
Trade Rating: +18
Location: Leicester
|
|
if you can get a know good coilpack aswell, itll rule that out aswell.
| | |
|
|
|
|
| | |
| NO LONGER ACTIVE ON THE FORUM | |
| | |
|
|
|
|
|
|
|
Posted: Wed Nov 09, 2011 4:24 pm |
|
|
|
|
Joined: Apr 09, 2011
Posts: 445
Trade Rating: +1
Location: letchworth
|
|
i want to try and resist buying a coil pack as i dont have that kinda money at the moment 
| | |
|
|
|
|
| | |
| if it dont scuff the ruff it aint low enuf | |
| | |
|
|
|
|
|
|
|
Posted: Wed Nov 09, 2011 4:27 pm |
|
|
|
|
Joined: Feb 07, 2010
Posts: 2248
Trade Rating: +18
Location: Leicester
|
|
no one on here who has the same coilpack that would let you try it?
| | |
|
|
|
|
| | |
| NO LONGER ACTIVE ON THE FORUM | |
| | |
|
|
|
|
|
Membership:
Latest: 
New Today: 0
New Yesterday: 0
Overall: 17125
Online Now [433]:
Visitors: 432
Members: 0
Staff Online Now:
Page Views:
General
Forums Home
Forum FAQ
Search
