|
Author
|
Message |
|
|
 Posted: Sat May 18, 2013 1:30 pm |
|
|
|
|
Joined: Apr 18, 2013
Posts: 186
Trade Rating: 0
Location: Ashington, Northumberland
|
 |
Ok, maybe the wrong forum but I didn't where else to put it.
I got a GTi spoiler today for a bargain price and there's only one thing I can't work out how to do to make it look mint so far.
It has Tigerseal on it and it's been taken off so roughly it's got old paint and primer attached to the old Tigerseal in places. That show you how well this stuff bonds.
This stuff is set rock hard on the spoiler and I need to take it off so I can fit it with new stuff to my car. There is always a solution to any form of glue no matter what it is. With Tigerseal being popular there must be some form of remover.
I'm not going to be the only one who needs help on this issue so all advice and help welcome
| |  |
|
|
 |
 | |  |
| I ain't nuts, I'm condiments, I've been promoted | |
 | |  |
|
|
|
|
|
|
|
Posted: Sat May 18, 2013 1:33 pm |
|
|
|
|
Joined: Oct 10, 2012
Posts: 1917
Trade Rating: +13
Location: Spalding
|
|
Probably best to cut most of it off with a knife then sand it?
| | |
|
|
|
|
|
|
|
|
|
|
Posted: Sat May 18, 2013 2:09 pm |
|
|
|
|
Joined: Apr 18, 2013
Posts: 186
Trade Rating: 0
Location: Ashington, Northumberland
|
|
Cheers Tolkien, it looks like a tough job but shows how tough Tigerseal is
| | |
|
|
|
|
| | |
| I ain't nuts, I'm condiments, I've been promoted | |
| | |
|
|
|
|
|
|
|
Posted: Sat May 18, 2013 2:21 pm |
|
|
|
|
Joined: Feb 07, 2010
Posts: 4455
Trade Rating: +1
Location: Essex
|
|
Chisel?
| | |
|
|
|
|
|
|
|
|
|
|
Posted: Sat May 18, 2013 2:45 pm |
|
|
|
|
Joined: Apr 18, 2013
Posts: 186
Trade Rating: 0
Location: Ashington, Northumberland
|
|
Looks that way E5 
| | |
|
|
|
|
| | |
| I ain't nuts, I'm condiments, I've been promoted | |
| | |
|
|
|
|
|
|
|
Posted: Sat May 18, 2013 3:27 pm |
|
|
|
|
Joined: Feb 10, 2010
Posts: 4266
Trade Rating: +4
Location: Palestine
|
|
just cut it,but be careful while doing so
| | |
|
|
|
|
|
|
|
|
|
|
Posted: Sat May 18, 2013 4:33 pm |
|
|
|
|
Joined: Jan 29, 2011
Posts: 6526
Trade Rating: +10
Location: Westhoughton, Lancashire
|
|
|
I've heard off all sorts of things to try and soften it. A hairdrier, petrol. T and G remover, paint thinner, nail varnish remover. Never tried any of them, and I would use any method involving solvents with caution just in case they damage the spoiler.
| | |
|
|
|
|
|
|
|
|
|
|
Posted: Sun May 19, 2013 4:45 pm |
|
|
|
|
Joined: Apr 18, 2013
Posts: 186
Trade Rating: 0
Location: Ashington, Northumberland
|
|
Cheers Macca and Timon, helpful as always guys. You would think there would be something that's designed to remove it as there's bound to be times there's residue from usage. I'll try to find out a way of contacting the manufacturer to see what they suggest and post the feedback I get
| | |
|
|
|
|
| | |
| I ain't nuts, I'm condiments, I've been promoted | |
| | |
|
|
|
|
|
|
|
Posted: Sun May 19, 2013 5:28 pm |
|
|
|
|
Joined: Sep 21, 2012
Posts: 52
Trade Rating: 0
Location: Desborough
|
|
I know its a long shot but silicone/sealant remover?
| | |
|
|
|
|
|
|
|
|
|
|
Posted: Mon May 20, 2013 2:20 am |
|
|
|
|
Joined: Jan 05, 2011
Posts: 2985
Trade Rating: +36
Location: North Manchester
|
|
I have had to remove the stuff twice, It was a very long process with a Stanley blade, A chisel and lots of time and sore fingers. Hence the reason I got asked to do another I turned it down. Way too much effort for what I charged 
I wouldn't suggest using solvents especially if you plan on painting the spoiler afterwards.
| | |
|
|
|
|
|
|
|
|
|
|
Posted: Mon May 20, 2013 2:40 am |
|
|
|
|
Joined: Nov 27, 2010
Posts: 11519
Trade Rating: +10
Location: What's it to you? ? ?
|
|
Dremel 
| | |
|
|
|
|
| | |
| Toyota C-HR GR Sport 2.0 Hybrid with JBL & Alcantara packs. | |
| | |
|
|
|
|
|
|
|
Posted: Mon May 20, 2013 2:57 am |
|
|
|
|
Joined: Feb 07, 2010
Posts: 2949
Trade Rating: +6
Location: Athens, Greece
|
|
Blade scraper, then wire-brush wheel attachment on a drill, then sand paper.
Only where new glue will cover it again so it won't show-up.
I doubt solvents would do sfa unless you tried paint-stripper in which case it will need masking all around.
| | |
|
|
|
|
| | |
| 1.4i, 2001, 3-door, China Blue
Repair safely - Drive safely | |
| | |
|
|
|
|
|
|
|
Posted: Mon May 20, 2013 3:49 pm |
|
|
|
|
Joined: Apr 18, 2013
Posts: 186
Trade Rating: 0
Location: Ashington, Northumberland
|
|
Cheers guys.
I've set to work with the stanley knife and God this stuff is tough. I'll get a wire brush attachment this week as I need one anyway for stripping my old wheels. And yeah Dave I won't be doing this again matey
| | |
|
|
|
|
| | |
| I ain't nuts, I'm condiments, I've been promoted | |
| | |
|
|
|
|
|
|
|
Posted: Mon May 20, 2013 6:45 pm |
|
|
|
|
Joined: Feb 07, 2010
Posts: 2949
Trade Rating: +6
Location: Athens, Greece
|
|
| HowlingMadMurdock wrote: |
Cheers guys.
I've set to work with the stanley knife and God this stuff is tough. I'll get a wire brush attachment this week as I need one anyway for stripping my old wheels. And yeah Dave I won't be doing this again matey |
Mind you don't damage any non-glued part.
Might be worth masking it before doing the brush.
| | |
|
|
|
|
| | |
| 1.4i, 2001, 3-door, China Blue
Repair safely - Drive safely | |
| | |
|
|
|
|
|
|
|
Posted: Tue May 21, 2013 6:06 am |
|
|
|
|
Joined: Apr 18, 2013
Posts: 186
Trade Rating: 0
Location: Ashington, Northumberland
|
|
Yeah I'll be masking it before the brush V. Whoever put the Tiger Seal on did a very clean job so it won't be too tricky using the brush but still better safe than sorry. There's a small brush attachment at B&Q for a couple of quid so I'll pick one up tomorrow and give it a go.
| | |
|
|
|
|
| | |
| I ain't nuts, I'm condiments, I've been promoted | |
| | |
|
|
|
|
|
Membership:
Latest: 
New Today: 0
New Yesterday: 0
Overall: 17126
Online Now [57]:
Visitors: 56
Members: 0
Staff Online Now:
Page Views:
General
Forums Home
Forum FAQ
Search
