|
Author
|
Message |
|
|
 Posted: Sun Aug 14, 2016 4:40 pm |
|
|
|
|
Joined: Aug 14, 2016
Posts: 10
Trade Rating: 0
Location: North Bucks
|
 |
Hi,
New to 206's but not new to stripping out engines etc. I am currently trying to replace blown head gasket on 1.4l 206 8v (2003). I have striped out the main drive belt and rocker cover and cam covers. Removed all cables and pipes and now need to fit 10mm and 6mm locking pins to stop any cam movement before I remove the cam belt and head. I could move the engine over when I started but now unable to manually move the engine to TDC even though the spark plugs are out.
Any ideas as to what could be stopping the engine (the engine was working fine, apart from head gasket, before I started so no major reason why it 'locks' in one place). I can jiggle the engine a bit but it jut will not rotate past a certain point.
Any ideas would be very welcome.
Best regards,
Zero.
| |  |
|
|
 |
|
|
|
|
|
|
Posted: Sun Aug 14, 2016 7:58 pm |
|
|
|
|
Joined: Feb 07, 2010
Posts: 7093
Trade Rating: +11
Location: Suffolk
|
|
The timing is incorrect, or the valve clearances are 10 million miles out
Did you pin it via the flywheel and camshaft?
| | |
|
|
|
|
 | |  |
| Team Impossible Possible
The only way of finding the limits of the possible is by going beyond them into the impossible - Arthur C. Clarke
Forged 1.6 Turbo
Click to see more
144Bhp @ 7PSi - 193.9Bhp @ 13psi
206 Gti Race Car
Click to see more
For all Race/Track Preparation, Feel Free to PM Me!
Whether its for a custom ratio gearbox or track-day alignment, I can help! | |
 | |  |
|
|
|
|
|
|
|
Posted: Mon Aug 15, 2016 6:29 am |
|
|
|
|
Joined: Jan 29, 2011
Posts: 6526
Trade Rating: +10
Location: Westhoughton, Lancashire
|
|
Is the car in gear? Silly question but amazing how many people don't check this when trying to turn an engine by hand.
| | |
|
|
|
|
|
|
|
|
|
|
Posted: Mon Aug 15, 2016 7:58 am |
|
|
|
|
Joined: Aug 14, 2016
Posts: 10
Trade Rating: 0
Location: North Bucks
|
|
Macca1411: I did check it was in neutral, but thank you for the hint.
Addaz: I have not been able to pin the two points yet as I am unable to turn the engine to the correct position. The cam belt is still on but not able to move to that final locking position.
Is there a way to remove the cylinder head and reset the timing later?
Best regards,
Zero.
| | |
|
|
|
|
|
|
|
|
|
|
Posted: Mon Aug 15, 2016 11:56 am |
|
|
|
|
Joined: Feb 08, 2010
Posts: 7045
Trade Rating: +5
Location: In the garage
|
|
Surely if it's all yet to be stripped apart you just need to make sure all pistons are at the same position I. E. Halfway up the bores and then take the head off? Lock the cam and crank when it's reassembled.
| | |
|
|
|
|
| | |
| 2001 GTi 138, Bilstein Sprint dampers, H&R springs, 21mm Peugeot Sport torsion bars, 22mm rear ARB, Peugeot Sport Group A wishbones, 283mm discs, Goodridge stainless hoses, Maniflow 304 grade 4-2-1 2.5" manifold and system, 200 cell cat, Richard Longman head, 45mm Jenvey throttle bodies, 9.5mm TB spacers, 90mm air horns, Jenvey throttle linkage, Jenvey fuel rail, Aeromotive and Goodridge fuel fittings and braided hose, ITG sausage filter, Radtec custom radiator, Piper Ultimate Road cams, Piper vernier pulleys, Omex 600 ECU. Saxo electric PAS pump, Vibra Technics engine mounts. Samco coolant hoses, TTV steel flywheel, 4.76 final drive ratio, 307 CC 180 ratios. 2019 BMW 530i. 2017 Mercedes C300 convertible. | |
| | |
|
|
|
|
|
|
|
Posted: Mon Aug 15, 2016 12:17 pm |
|
|
|
|
Joined: Aug 14, 2016
Posts: 10
Trade Rating: 0
Location: North Bucks
|
|
Edward, I am just being cautious as I do not wish to dismantle and not be able to set up the timing correctly afterwards. Are you aware of a manual timing routine?
Best regards,
Zero.
| | |
|
|
|
|
|
|
|
|
|
|
Posted: Tue Aug 16, 2016 1:24 pm |
|
|
|
|
Joined: Feb 07, 2010
Posts: 3085
Trade Rating: +12
Location: Essex
|
|
Has there been water in the bore?
Is there maybe a rust ridge stopping the piston coming up the bore.
On a different note.... never turn your engine over using the cams.... always the bottom crank pulley.
| | |
|
|
|
|
|
|
|
|
|
|
Posted: Tue Aug 16, 2016 2:07 pm |
|
|
|
|
Joined: Feb 08, 2010
Posts: 7045
Trade Rating: +5
Location: In the garage
|
|
| ElectronZero wrote: |
Edward, I am just being cautious as I do not wish to dismantle and not be able to set up the timing correctly afterwards. Are you aware of a manual timing routine?
. |
There won't be anything to stop you putting it back together and timing it properly later.
| | |
|
|
|
|
| | |
| 2001 GTi 138, Bilstein Sprint dampers, H&R springs, 21mm Peugeot Sport torsion bars, 22mm rear ARB, Peugeot Sport Group A wishbones, 283mm discs, Goodridge stainless hoses, Maniflow 304 grade 4-2-1 2.5" manifold and system, 200 cell cat, Richard Longman head, 45mm Jenvey throttle bodies, 9.5mm TB spacers, 90mm air horns, Jenvey throttle linkage, Jenvey fuel rail, Aeromotive and Goodridge fuel fittings and braided hose, ITG sausage filter, Radtec custom radiator, Piper Ultimate Road cams, Piper vernier pulleys, Omex 600 ECU. Saxo electric PAS pump, Vibra Technics engine mounts. Samco coolant hoses, TTV steel flywheel, 4.76 final drive ratio, 307 CC 180 ratios. 2019 BMW 530i. 2017 Mercedes C300 convertible. | |
| | |
|
|
|
|
|
|
|
Posted: Fri Aug 19, 2016 7:35 pm |
|
|
|
|
Joined: Aug 14, 2016
Posts: 10
Trade Rating: 0
Location: North Bucks
|
|
Macj: Not sure if water got in but I could turn the engine when it had spark plugs in but since taking them out I can no longer move the engine around....
Edward: I am unable to find any details of how to set the timing up if the locks are not in position. Can you point me to where I can find details on this (I have the Haynes Manual - but no details there)
Many thanks to you all for taking the time in replying.
Best regards,
Zero
| | |
|
|
|
|
|
|
|
|
|
|
Posted: Sat Aug 20, 2016 9:57 am |
|
|
|
|
Joined: Feb 07, 2010
Posts: 3085
Trade Rating: +12
Location: Essex
|
|
Whip the head off.... the timing is relatively easy once you know what your looking at inside. If you have any issues in the bores you will have to deal with that first.... setting the timing up is a case of matching a diagram of timing points which we can find.
| | |
|
|
|
|
|
|
|
|
|
|
Posted: Sat Aug 20, 2016 1:00 pm |
|
|
|
|
Joined: Aug 14, 2016
Posts: 10
Trade Rating: 0
Location: North Bucks
|
|
Macj: Head is off - very messy 
I am going to get head skimmed as quite pitted and then rebuild from there. Where can I find details of the timing points or do I just move the engine to the two lock points, lock them and rebuild?
| | |
|
|
|
|
|
|
|
|
|
|
Posted: Sat Aug 20, 2016 2:47 pm |
|
|
|
|
Joined: Jan 29, 2011
Posts: 6526
Trade Rating: +10
Location: Westhoughton, Lancashire
|
|
Don't turn the crank with the head off as you risk disturbing the cylinder liners
| | |
|
|
|
|
|
|
|
|
|
|
Posted: Sat Aug 20, 2016 5:18 pm |
|
|
|
|
Joined: Nov 27, 2010
Posts: 11519
Trade Rating: +10
Location: What's it to you? ? ?
|
|
| macca1411 wrote: |
| Don't turn the crank with the head off as you risk disturbing the cylinder liners |
Correct, you need special locking tools to lock the liners in position if you wish to turn the crank with the head removed.
| | |
|
|
|
|
| | |
| Toyota C-HR GR Sport 2.0 Hybrid with JBL & Alcantara packs. | |
| | |
|
|
|
|
|
|
|
Posted: Sun Aug 21, 2016 11:05 am |
|
|
|
|
Joined: Aug 14, 2016
Posts: 10
Trade Rating: 0
Location: North Bucks
|
|
Thanks for the info. I will proceed with caution. I have a day or so of work just to clean out all the contaminated water from the block before rebuilding.
| | |
|
|
|
|
|
|
|
|
|
|
Posted: Sun Aug 21, 2016 3:33 pm |
|
|
|
|
Joined: Feb 07, 2010
Posts: 3085
Trade Rating: +12
Location: Essex
|
|
You only have to pop a piece of angle iron across the liner tops to stop them from moving but it sounds like a liner moving is the least of your worried... I think if the head is pitted you may need a replacement second hand engine.. . It may be cheaper in the long run
| | |
|
|
|
|
|
|
|
|
Membership:
Latest: 
New Today: 1
New Yesterday: 0
Overall: 17127
Online Now [55]:
Visitors: 54
Members: 0
Staff Online Now:
Page Views:
General
Forums Home
Forum FAQ
Search
