The Peugeot 206 Info Exchange › Forums › The Car › 206 Problems

Forums Home

Forum FAQ

Refitting Gearbox problem
Forum Index › 206 Problems

watchs.gif

Author

Message

SamanthasHubby

Posted: Mon Jun 04, 2018 5:47 am

Joined: May 02, 2018
Posts: 8
Trade Rating: 0
Location: Scunthorpe

Hi all

Has anyone got any ideas on how I can refit the gearbox on my 206?

Took it out to replace the clutch and now cannot get it back in! I cannot get the intermediate driveshaft bearing out of the holder (yes undone the bearing clamps Very Happy

) so having to try and line up both shafts at the same time (first motion and the intermediate driveshaft)

The problems seems to be the driveshaft not locating

Any ideas??

Frustrated in Scunthorpe!

Steve206

Posted: Mon Jun 04, 2018 4:40 pm

Joined: Feb 07, 2010
Posts: 2716
Trade Rating: +6
Location: UK

What engine and box is it? Usually easier to fit and then add driveshaft after. Have you also replaced the driveshaft seals. Pain to put it all together and then find your seals need changing!


	Work in Progress

Indigo_GTI

Posted: Mon Jun 04, 2018 7:10 pm

Joined: Feb 08, 2010
Posts: 106
Trade Rating: 0
Location: Aberdeenshire

I agree with Steve about the driveshaft, its sounds like a nightmare trying to fit it like that. It may well be the teeth are out slightly which is why it wont locate, you could try to rotate the driveshaft a few times so that the teeth line up.
When you say you have undone the bearing clamps, have you just removed the nuts? On my GTI the retaining bolts have a cam lobe style end, so you need to rotate the bolts themselves to clear the bearing before it will come out. Its not that easy to see when they are actually clear as well, i always found a small telescopic mirror a great help to see when the bolts are clear.
Did you also make sure the new clutch is properly aligned as if thats not right you wont get it back in.


	.

SamanthasHubby

Posted: Wed Jun 06, 2018 4:27 am

Joined: May 02, 2018
Posts: 8
Trade Rating: 0
Location: Scunthorpe

Hi guys
It’s a 1.1 with an MA5 gearbox.

I tried rotating the prop and the engine to see if it was just allignment and no joy - left it a day and went back to it, kicked the gearbox half heartedly and it popped in!

It was a pig to get in with the prop in the way and I had rotated the bearing clamps out of the way but the bearing was stuck fast.

Next time a garage can have the hassle!

Thanks for the replies - need to read the forum before I attempt anything next time Wink

Edward

Posted: Wed Jun 06, 2018 10:56 am

Joined: Feb 08, 2010
Posts: 7042
Trade Rating: +5
Location: In the garage

Why not remove the whole mount that the bearing is attached To?


	2001 GTi 138, Bilstein Sprint dampers, H&R springs, 21mm Peugeot Sport torsion bars, 22mm rear ARB, Peugeot Sport Group A wishbones, 283mm discs, Goodridge stainless hoses, Maniflow 304 grade 4-2-1 2.5" manifold and system, 200 cell cat, Richard Longman head, 45mm Jenvey throttle bodies, 9.5mm TB spacers, 90mm air horns, Jenvey throttle linkage, Jenvey fuel rail, Aeromotive and Goodridge fuel fittings and braided hose, ITG sausage filter, Radtec custom radiator, Piper Ultimate Road cams, Piper vernier pulleys, Omex 600 ECU. Saxo electric PAS pump, Vibra Technics engine mounts. Samco coolant hoses, TTV steel flywheel, 4.76 final drive ratio, 307 CC 180 ratios. 2019 BMW 530i. 2017 Mercedes C300 convertible.

watchs.gif		All times are GMT
Forum Index › 206 Problems Page 1 of 1


	You cannot post new topics in this forum You cannot reply to topics in this forum You cannot edit your posts in this forum You cannot delete your posts in this forum You cannot vote in polls in this forum You cannot attach files in this forum You can download files in this forum