New Here?
Toggle Content
   

Toggle Content User Info
Welcome

Anonymous

Nickname
Password
Register

Membership:
Latest: DanDan17
New Today: 0
New Yesterday: 0
Overall: 17128

Online Now [45]:
Visitors: 44
Bots: 1
Members: 0
Staff Online Now:

No staff members are online!
Page Views:
Today: 37984
Total: 100557874

Toggle Content Main Menu
 General Info Goodies Search Web Stats Members
 Donations

 

Forums › The Car › 206 Problems › Why you should change your cambelt!


 
 

Why you should change your cambelt!
Forum Index206 Problems
Reply to topic Printer Friendly Page watchs.gif View Previous Topic View Next Topic
Author
Message
rob_1990
PostPosted: Thu Feb 24, 2011 4:02 pm Up
Full on 206 Owner


Offline

Joined: Feb 08, 2010
Posts: 100
Trade Rating: +1
Location: Cambridge UK


Well as some as you know by now i have been having problems with my car for the last month or so... It's been at my local garage for the last 2 weeks as it developed into an almost non running state.

The last time i drove it, it lost loads of power and sounded noisy which made me worry. So i slowly managed to make it home. The next day i went to run it up to the garage so they could tell me whats wrong with it when it made a horrible clangy noise and started running on 2 cylinders. A week later they found time to get the head off of it as it failed a compression test.

Once the head was off they noticed a few bent valves! It was then discovered that the cambelt has skipped a few teeth on the cam shaft and put the timing so out the pistons have hit the valves. So as replacing the valves on the engine is a very involved job the garage now have sent the head to an engine specialist to fit the valves. On their inspection it turns out that the valve seats are damaged and the head needs re-conditioning or replacing. Turns out most valves are bent some more than others.

I think they said the pistons and bottom end seem fine, which in a way is good news. They say the cause of the problem is that the water pump may have seized and caused the cambelt to fail.

The horrible thing for me is i had the car booked in for a cambelt change a few days after it went.

Now im faced with a huge bill rather than just a slightly expensive bill for a new cambelt and water pump Sad

Good news is that hopefully the engine will be as good as new when its all back and running. The garage will replace the cambelt, waterpump and the head gasket. Also as i know them well they are doing all the bits at cost price and making it as cheap as possible.

I shall keep you updated on any advances.

 
View user's profile
Seabook
PostPosted: Thu Feb 24, 2011 4:16 pm Up
Custom - Green Stars


Offline

Joined: Feb 08, 2010
Posts: 10151
Trade Rating: +12


sorry to heard that but as far as i know some 180Gti slip their belt as early as 30K!

so you only get the head re-cond?

to be fair it would be safer to check the bottom as well

 
 

 

Car Sold....
View user's profile
rob_1990
PostPosted: Thu Feb 24, 2011 4:21 pm Up
Full on 206 Owner


Offline

Joined: Feb 08, 2010
Posts: 100
Trade Rating: +1
Location: Cambridge UK


I think they have had the pistons out aswell, i just went and had a cheaky look with the spare key and all 4 pistons are at the same height?? it needs a new head or re-conditioning. i think they will make it like brand new and polish it.
 
View user's profile
macca1411
PostPosted: Thu Feb 24, 2011 4:28 pm Up
Staff - Moderator


Offline

Joined: Jan 29, 2011
Posts: 6526
Trade Rating: +10
Location: Westhoughton, Lancashire


I take it the pistons are half way down the cylinder if they are at the same height. It is unlikely that the con rods or the crank will be damaged. I have known valves to leave indentations on the piston crowns, but thats nothing serious. It's amazing how much damage can be caused by the timing being a few degrees out.
View user's profile
MrrNoName
PostPosted: Thu Feb 24, 2011 4:49 pm Up
206 Crazy


Offline

Joined: Dec 16, 2010
Posts: 1533
Trade Rating: +10
Location: UK


just out of interest, how many miles does the engine have on it? and whats the age of the car Razz ?
Please Dont take any of my posts as written fact. They are simply my opinion and although to the best of my knowledge true, the information within them may well be incorrect.

Any work you undertake as a result of my posts is done so at your own risk Smile
View user's profile
rob_1990
PostPosted: Thu Feb 24, 2011 5:03 pm Up
Full on 206 Owner


Offline

Joined: Feb 08, 2010
Posts: 100
Trade Rating: +1
Location: Cambridge UK


It has 62k and is a 2004 53 plate.
 
View user's profile
bellevuespares
PostPosted: Thu Feb 24, 2011 5:40 pm Up
Dedicated Member


Offline

Joined: Nov 28, 2010
Posts: 521
Trade Rating: +9
Location: Manchester


whats the cost of repair?
Sig removed due to size
PEUGEOT 206 & FIAT PUNTO Replacement Parts at Bellevue Spares Manchester.
We also offer a fitting service! Free Quotes!
View user's profile Visit poster's website
Lee.
PostPosted: Thu Feb 24, 2011 6:40 pm Up
Loving the 206 Experience


Offline

Joined: Mar 28, 2010
Posts: 334
Trade Rating: +1
Location: Blackwood, South Wales


I had my 53 plate done at 49k, just peace of mind I guess. Sorry it went though fella, but could've been sooo much worse!
 
View user's profile
ExoVyper
PostPosted: Thu Feb 24, 2011 7:31 pm Up
206 Crazy


Offline

Joined: Feb 07, 2010
Posts: 1495
Trade Rating: +3
Location: Waiting for the tugboats to push me into port (Whitehaven)


just so you know this will jsut be the valves and head as for a valve to damage a piston ( apart from marking the top of the piston) is practically unheard of.

i've known one drop a valve right into the bore and the piston battered the hell out of it but didn't bend the con rods or anything

 

Current car:HMS Vectra Very Happy
View user's profile
rob_1990
PostPosted: Fri Feb 25, 2011 1:56 am Up
Full on 206 Owner


Offline

Joined: Feb 08, 2010
Posts: 100
Trade Rating: +1
Location: Cambridge UK


Yeah i think the valves took the lot of it, i doubt the bottom end will be a problem. Cost of repair will be about 750 quid. The head is costing £450 to recondition and the garage are only charging me for around 4 hours labour instead of 6-7.
 
View user's profile
Reply to topic Printer Friendly Page watchs.gif View Previous Topic View Next Topic All times are GMT
Forum Index206 Problems

Page 1 of 1
  You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum
You cannot attach files in this forum
You can download files in this forum

 
We are not responsible for comments posted by our users, as they are the property of the poster
Interactive software released under GNU GPL, Code Credits, Privacy Policy