|
Author
|
Message |
|
|
 Posted: Fri Mar 18, 2011 1:21 pm |
|
|
|
|
Joined: Mar 01, 2010
Posts: 515
Trade Rating: 0
Location: Nuneaton
|
 |
Hey Guys,
Had a throttle position problem, so took the throttle body off to give it a clean, wiped all the inside of it out and got all the muck out and then put it back on the car.
Put it back on car, fitted induction etc and then started it up and it revved to 2k straight away and keeps going up and down from 1.5k to 2k revs.
Any ideas what this could be?
Lewis
| |  |
|
|
 |
 | |  |
| 206 1.6 16v, Nimrods, Full SP Kit, 3 Stage Valve Cut Head, 4-1 Manifold With Decat, Pug Sport Backbox, Vibe Speakers, HIDs In Projectors, DVD screens & Sub  | |
 | |  |
|
|
|
|
|
|
|
Posted: Fri Mar 18, 2011 1:30 pm |
|
|
|
|
Joined: Feb 10, 2011
Posts: 84
Trade Rating: +1
Location: Bolton
|
|
could be your icv mate
| | |
|
|
|
|
|
|
|
|
|
|
Posted: Fri Mar 18, 2011 1:32 pm |
|
|
|
|
Joined: Mar 01, 2010
Posts: 515
Trade Rating: 0
Location: Nuneaton
|
|
Would me of cleaning the throttle body have affected it?
Lewis
| | |
|
|
|
|
| | |
| 206 1.6 16v, Nimrods, Full SP Kit, 3 Stage Valve Cut Head, 4-1 Manifold With Decat, Pug Sport Backbox, Vibe Speakers, HIDs In Projectors, DVD screens & Sub | |
| | |
|
|
|
|
|
|
|
Posted: Fri Mar 18, 2011 1:35 pm |
|
|
|
|
Joined: Feb 08, 2010
Posts: 5400
Trade Rating: +105
Location: Stafford
|
|
Wouldn't have thought so but you could have tampered with it whilst doing so. Just getting it off, cleaning it and re fitting would be your first step.
| | |
|
|
|
|
|
|
|
|
|
|
Posted: Fri Mar 18, 2011 1:36 pm |
|
|
|
|
Joined: Mar 01, 2010
Posts: 515
Trade Rating: 0
Location: Nuneaton
|
|
Harry, I took it off and refitted it. I even put on another throttle body I have in my garage... Still no luck...
Lewis
| | |
|
|
|
|
| | |
| 206 1.6 16v, Nimrods, Full SP Kit, 3 Stage Valve Cut Head, 4-1 Manifold With Decat, Pug Sport Backbox, Vibe Speakers, HIDs In Projectors, DVD screens & Sub | |
| | |
|
|
|
|
|
|
|
Posted: Fri Mar 18, 2011 1:46 pm |
|
|
|
|
Joined: Feb 08, 2010
Posts: 5400
Trade Rating: +105
Location: Stafford
|
|
You replaced the whole throttle body and the same thing still happened?
| | |
|
|
|
|
|
|
|
|
|
|
Posted: Fri Mar 18, 2011 1:49 pm |
|
|
|
|
Joined: Feb 08, 2010
Posts: 7045
Trade Rating: +5
Location: In the garage
|
|
The 16V doesn't have an idle control valve does it?
| | |
|
|
|
|
| | |
| 2001 GTi 138, Bilstein Sprint dampers, H&R springs, 21mm Peugeot Sport torsion bars, 22mm rear ARB, Peugeot Sport Group A wishbones, 283mm discs, Goodridge stainless hoses, Maniflow 304 grade 4-2-1 2.5" manifold and system, 200 cell cat, Richard Longman head, 45mm Jenvey throttle bodies, 9.5mm TB spacers, 90mm air horns, Jenvey throttle linkage, Jenvey fuel rail, Aeromotive and Goodridge fuel fittings and braided hose, ITG sausage filter, Radtec custom radiator, Piper Ultimate Road cams, Piper vernier pulleys, Omex 600 ECU. Saxo electric PAS pump, Vibra Technics engine mounts. Samco coolant hoses, TTV steel flywheel, 4.76 final drive ratio, 307 CC 180 ratios. 2019 BMW 530i. 2017 Mercedes C300 convertible. | |
| | |
|
|
|
|
|
|
|
Posted: Fri Mar 18, 2011 1:50 pm |
|
|
|
|
Joined: Feb 07, 2010
Posts: 2248
Trade Rating: +18
Location: Leicester
|
|
Did you put the gasket back on and tighten it up? Sounds like either an air leak or you might need to reset the ecu via unplugging the battery for 30 mins then letting it idle on its own for a couple of minutes.
| | |
|
|
|
|
| | |
| NO LONGER ACTIVE ON THE FORUM | |
| | |
|
|
|
|
|
|
|
Posted: Fri Mar 18, 2011 1:50 pm |
|
|
|
|
Joined: Feb 07, 2010
Posts: 5120
Trade Rating: +19
Location: Raunds, Northamptonshire
|
|
make sure there in no air leak between the throttle body and intake manifold and gasket is ok.
EDIT: as above me. 
| | |
|
|
|
|
|
|
|
|
|
|
Posted: Fri Mar 18, 2011 1:53 pm |
|
|
|
|
Joined: Mar 01, 2010
Posts: 515
Trade Rating: 0
Location: Nuneaton
|
|
there's a tiny little gap between the inlet and throttle body but i thought it was normal... should i tap it on with a hammer so its on mega tight, leave the battery off for 30 mins and reset ecu too?
Lewis
| | |
|
|
|
|
| | |
| 206 1.6 16v, Nimrods, Full SP Kit, 3 Stage Valve Cut Head, 4-1 Manifold With Decat, Pug Sport Backbox, Vibe Speakers, HIDs In Projectors, DVD screens & Sub | |
| | |
|
|
|
|
|
|
|
Posted: Fri Mar 18, 2011 1:53 pm |
|
|
|
|
Joined: Mar 01, 2010
Posts: 515
Trade Rating: 0
Location: Nuneaton
|
|
By the way guys, gasket? there was no gasket....
| | |
|
|
|
|
| | |
| 206 1.6 16v, Nimrods, Full SP Kit, 3 Stage Valve Cut Head, 4-1 Manifold With Decat, Pug Sport Backbox, Vibe Speakers, HIDs In Projectors, DVD screens & Sub | |
| | |
|
|
|
|
|
|
|
Posted: Sat Mar 19, 2011 8:12 pm |
|
|
|
|
Joined: Mar 01, 2010
Posts: 515
Trade Rating: 0
Location: Nuneaton
|
|
Sorted! just needed error code erasing!
| | |
|
|
|
|
| | |
| 206 1.6 16v, Nimrods, Full SP Kit, 3 Stage Valve Cut Head, 4-1 Manifold With Decat, Pug Sport Backbox, Vibe Speakers, HIDs In Projectors, DVD screens & Sub | |
| | |
|
|
|
|
|
|
|
Posted: Sat Mar 19, 2011 9:23 pm |
|
|
|
|
Joined: Feb 07, 2010
Posts: 2949
Trade Rating: +6
Location: Athens, Greece
|
|
weird.
| | |
|
|
|
|
| | |
| 1.4i, 2001, 3-door, China Blue
Repair safely - Drive safely | |
| | |
|
|
|
|
|
|
|
Posted: Sun Mar 20, 2011 6:53 am |
|
|
|
|
Joined: Mar 01, 2010
Posts: 515
Trade Rating: 0
Location: Nuneaton
|
|
Very! All sorted now! Im not complaining. It is now popping and banging now!
| | |
|
|
|
|
| | |
| 206 1.6 16v, Nimrods, Full SP Kit, 3 Stage Valve Cut Head, 4-1 Manifold With Decat, Pug Sport Backbox, Vibe Speakers, HIDs In Projectors, DVD screens & Sub | |
| | |
|
|
|
|
|
Membership:
Latest: 
New Today: 0
New Yesterday: 0
Overall: 17128
Online Now [57]:
Visitors: 56
Members: 0
Staff Online Now:
Page Views:
General
Forums Home
Forum FAQ
Search
