|
Author
|
Message |
|
|
 Posted: Fri Nov 04, 2016 7:24 pm |
|
|
|
|
Joined: Feb 08, 2010
Posts: 526
Trade Rating: 0
Location: Italy
|
 |
Any advice on this, please?
It happens after coilover install, just under acceleration; angles have been checked...
| |  |
|
|
 |
 | |  |
| Silver grey RC|Pug Sport remap|Group A induction|Supersprint backbox|lower strut bar|RCCup wishbones|Eibach Pro-Street-S|302mm brakes+23.8 master cylinder|Vibra Technics|Quaife LSD|Cupra R splitter|modded bonnet vent|black Valeos|207i tail lights|Chromed rear foglight|Bi-xenon 6000k+all led (in+out)|406 rear mirror | |
 | |  |
|
|
|
|
|
|
|
Posted: Fri Nov 04, 2016 10:36 pm |
|
|
|
|
Joined: Jun 20, 2012
Posts: 1160
Trade Rating: +1
Location: West Country
|
|
Check if your coilovers are adjusted equally for damping/rebound and height and are otherwise in good working order
This thread pretty much sums it up all corner cases and what not  www.206info.co.uk/Foru...89655.html
| | |
|
|
|
|
|
|
|
|
|
|
Posted: Sat Nov 05, 2016 12:32 pm |
|
|
|
|
Joined: Feb 08, 2010
Posts: 526
Trade Rating: 0
Location: Italy
|
|
Lower arms are the major culprit in this cases, but mine are new and genuine...
| | |
|
|
|
|
| | |
| Silver grey RC|Pug Sport remap|Group A induction|Supersprint backbox|lower strut bar|RCCup wishbones|Eibach Pro-Street-S|302mm brakes+23.8 master cylinder|Vibra Technics|Quaife LSD|Cupra R splitter|modded bonnet vent|black Valeos|207i tail lights|Chromed rear foglight|Bi-xenon 6000k+all led (in+out)|406 rear mirror | |
| | |
|
|
|
|
|
|
|
Posted: Sat Nov 05, 2016 12:39 pm |
|
|
|
|
Joined: Jun 20, 2012
Posts: 1160
Trade Rating: +1
Location: West Country
|
|
In my case they were also newly fitted wishbones, I was sure they were fine, so went checking through all other possibilities that might contribute to the pulling.
If your ones are genuine, that list is still useful to find the real culprit.
It's all about forces that come in effect when torque is applied to the relevant suspension components, and the extent of that relevance.
| | |
|
|
|
|
|
|
|
|
|
|
Posted: Sat Nov 05, 2016 12:59 pm |
|
|
|
|
Joined: Feb 08, 2010
Posts: 526
Trade Rating: 0
Location: Italy
|
|
I never heard of wishbones consumption, what's the thing to check?
| | |
|
|
|
|
| | |
| Silver grey RC|Pug Sport remap|Group A induction|Supersprint backbox|lower strut bar|RCCup wishbones|Eibach Pro-Street-S|302mm brakes+23.8 master cylinder|Vibra Technics|Quaife LSD|Cupra R splitter|modded bonnet vent|black Valeos|207i tail lights|Chromed rear foglight|Bi-xenon 6000k+all led (in+out)|406 rear mirror | |
| | |
|
|
|
|
|
|
|
Posted: Sat Nov 05, 2016 1:04 pm |
|
|
|
|
Joined: Jun 20, 2012
Posts: 1160
Trade Rating: +1
Location: West Country
|
|
The two bushes of each wishbone that mount inside subframe.
Use a prybar to gently bend a wishbone up or down (when car is jacked up they are opening up nicely already on standard suspension height).
Check for tearing and general condition of rubber behind the metal ring (I assume you have the GTi wishbones)
| | |
|
|
|
|
|
|
|
|
|
|
Posted: Sun Nov 06, 2016 2:18 pm |
|
|
|
|
Joined: Feb 08, 2010
Posts: 526
Trade Rating: 0
Location: Italy
|
|
Thanks, sorry, my fault. I thought that "wishbones" were swivel pins, not lower arms (that are new)... My fault in translation... 
| | |
|
|
|
|
| | |
| Silver grey RC|Pug Sport remap|Group A induction|Supersprint backbox|lower strut bar|RCCup wishbones|Eibach Pro-Street-S|302mm brakes+23.8 master cylinder|Vibra Technics|Quaife LSD|Cupra R splitter|modded bonnet vent|black Valeos|207i tail lights|Chromed rear foglight|Bi-xenon 6000k+all led (in+out)|406 rear mirror | |
| | |
|
|
|
|
|
|
|
Posted: Wed Nov 09, 2016 5:01 pm |
|
|
|
|
Joined: Jun 19, 2010
Posts: 1600
Trade Rating: +4
Location: South Bucks
|
|
Check you have the GTI arms. If they have fitted standard arms the bushes will fail very quickly .. as will cheap, low quality arms.
| | |
|
|
|
|
| | |
| Down to just the 1.4 HDi. Cayman Green 2.0i CC sold. | |
| | |
|
|
|
|
|
|
|
Posted: Wed Nov 09, 2016 8:39 pm |
|
|
|
|
Joined: Feb 08, 2010
Posts: 526
Trade Rating: 0
Location: Italy
|
|
| gazza82 wrote: |
| Check you have the GTI arms. If they have fitted standard arms the bushes will fail very quickly .. as will cheap, low quality arms. |
Thanks, they are the GTi ones; but in effects I replaced a lot of them because of the GTi jointball...
Never had any issue with 1.6 gummy bushes.
| | |
|
|
|
|
| | |
| Silver grey RC|Pug Sport remap|Group A induction|Supersprint backbox|lower strut bar|RCCup wishbones|Eibach Pro-Street-S|302mm brakes+23.8 master cylinder|Vibra Technics|Quaife LSD|Cupra R splitter|modded bonnet vent|black Valeos|207i tail lights|Chromed rear foglight|Bi-xenon 6000k+all led (in+out)|406 rear mirror | |
| | |
|
|
|
|
|
Membership:
Latest: 
New Today: 0
New Yesterday: 0
Overall: 17116
Online Now [20]:
Visitors: 19
Members: 0
Staff Online Now:
Page Views:
General
Forums Home
Forum FAQ
Search
