|
Author
|
Message |
|
|
 Posted: Tue Mar 29, 2011 1:07 pm |
|
|
|
|
Joined: Feb 08, 2010
Posts: 10151
Trade Rating: +12
|
 |
one arm off already, easier than i though, and definitely easier than do the torsion bar
| |  |
|
|
 |
|
|
|
|
|
|
Posted: Tue Mar 29, 2011 5:11 pm |
|
|
|
|
Joined: Mar 21, 2010
Posts: 75
Trade Rating: 0
Location: Devon
|
|
near side is easier, if i have a car parked next to me tommorow im fooked as i wont be able to get the arb out lol
Oh can anyone tell me what size bolt you need to get the arb plate out (if you know what i mean, the triangle shaped plate attached to the swing arm?
| | |
|
|
|
|
Last edited by mcfly666 on Tue Mar 29, 2011 5:20 pm; edited 1 time in total
|
|
|
|
|
|
|
Posted: Tue Mar 29, 2011 5:19 pm |
|
|
|
|
Joined: Feb 08, 2010
Posts: 10151
Trade Rating: +12
|
|
| mcfly666 wrote: |
| near side is easier, if i have a car parked next to me tommorow im fooked as i wont be able to get the arb out lol |
just the same to me 
as the axle is not on the car atm
i think i might give it a polish before i put it on 
| | |
|
|
|
|
|
|
|
|
|
|
Posted: Tue Mar 29, 2011 5:21 pm |
|
|
|
|
Joined: Mar 21, 2010
Posts: 75
Trade Rating: 0
Location: Devon
|
|
Yeah and loads of grease matie! I put a bit extra on my post above me, any help would be handy 
| | |
|
|
|
|
|
|
|
|
|
|
Posted: Wed Mar 30, 2011 5:39 am |
|
|
|
|
Joined: Feb 07, 2010
Posts: 2720
Trade Rating: +6
Location: UK
|
|
| mcfly666 wrote: |
near side is easier, if i have a car parked next to me tommorow im fooked as i wont be able to get the arb out lol
Oh can anyone tell me what size bolt you need to get the arb plate out (if you know what i mean, the triangle shaped plate attached to the swing arm? |
If you have rear discs, use a bolt from the caliber, if not you could try a front caliper bolt.
| | |
|
|
|
|
|
|
|
|
|
|
Posted: Wed Mar 30, 2011 5:58 am |
|
|
|
|
Joined: Feb 08, 2010
Posts: 10151
Trade Rating: +12
|
|
| mcfly666 wrote: |
| Yeah and loads of grease matie! I put a bit extra on my post above me, any help would be handy |
M12 1.5thread bolt
| | |
|
|
|
|
|
|
|
|
|
|
Posted: Wed Mar 30, 2011 9:52 am |
|
|
|
|
Joined: Mar 21, 2010
Posts: 75
Trade Rating: 0
Location: Devon
|
|
thanks guys, got a M12 from bnq and it fitted (blind luck) job is done now, stub pin wasnt too bad after a good sand and wire brushing with a dremel. hardes part was banging the bearing in, the torsion bar would not move so I had to free it up from the other side and do the work on the trailing arm with the torsion bar fapping around :/
Who knows how long it will last:P
| | |
|
|
|
|
|
|
|
|
|
|
Posted: Wed Mar 30, 2011 4:14 pm |
|
|
|
|
Joined: Feb 08, 2010
Posts: 10151
Trade Rating: +12
|
|
how did you bang in the bearing?
i am still removing the left overbit inside the trailing arm lol
i was considering to pay the garage to press the bearing in for me lol
| | |
|
|
|
|
|
|
|
|
|
|
Posted: Thu Mar 31, 2011 12:17 pm |
|
|
|
|
Joined: Mar 21, 2010
Posts: 75
Trade Rating: 0
Location: Devon
|
|
Banged the inside bearing in with a piece of wood (it has a lip on it) the outer bearing I banged in with wood untill flush and finished it of with a piece of 52/51mm bar, it sits inside the trailing arm about 1/4 of an inch.
| | |
|
|
|
|
|
|
|
|
|
|
Posted: Thu Mar 31, 2011 2:24 pm |
|
|
|
|
Joined: Feb 07, 2010
Posts: 2720
Trade Rating: +6
Location: UK
|
|
Anyone got any pics of what theyve been doing?
| | |
|
|
|
|
|
|
|
|
|
|
Posted: Sat Apr 02, 2011 7:29 am |
|
|
|
|
Joined: Mar 21, 2010
Posts: 75
Trade Rating: 0
Location: Devon
|
|
I dont steve, my job is all finished  There is a guide on youtube which might help you (I posted near the start of the thread)
| | |
|
|
|
|
|
|
|
|
Membership:
Latest: 
New Today: 0
New Yesterday: 0
Overall: 17130
Online Now [493]:
Visitors: 492
Members: 0
Staff Online Now:
Page Views:
General
Forums Home
Forum FAQ
Search
