|
Author
|
Message |
|
|
 Posted: Mon Apr 11, 2011 10:25 am |
|
|
|
|
Joined: Jul 02, 2010
Posts: 63
Trade Rating: 0
Location: Coventry
|
 |
Ok so went to do my MOT today thinking it would pass but failed on 10 seperate points!! 
1. Offside registration plate lamp not working
2. Offside headlamp aim too high
3. Offside front constant velocity joint gaiter insecurely mounted to its housing
4. Nearside balljoint
5. Offside balljoint
6. Nearside rear shock absorber has an excessively worn rubber bush
7. Rear brake load sensing valve linkage seized
8. Front (pipe) exhaust has a major leak of exhaust gases
9. Exhaust emmissions carbon monoxide content after 2nd fast idle excessive
10. Exhaust emmissions lambda reading after 2nd fast idle outside specified limits
Most of it seems quite simple to do but can anyone tell me whats involved and how much the constant velocity gaiter, the rubber bush on the shock and the rear brake valve are likely to cost to fix?
| |  |
|
|
 |
 | |  |
| W reg 1.4 lx in diablo red. lowered and with 17 inch konig alloys | |
 | |  |
|
|
|
|
|
|
|
Posted: Mon Apr 11, 2011 10:27 am |
|
|
|
|
Joined: Feb 07, 2010
Posts: 5575
Trade Rating: +33
Location: Moscow
|
|
CV Gaiter means removal of Driveshaft IIRC.
New Shock.
and lots of WD40 on brake valve.
| | |
|
|
|
|
|
|
|
|
|
|
Posted: Mon Apr 11, 2011 10:31 am |
|
|
|
|
Joined: Jul 02, 2010
Posts: 63
Trade Rating: 0
Location: Coventry
|
|
| tomd0801754 wrote: |
CV Gaiter means removal of Driveshaft IIRC.
New Shock.
and lots of WD40 on brake valve. |
No way to fix the old shock? Its not a standard one otherwise I wouldn't bother fixing would just buy a new one
| | |
|
|
|
|
| | |
| W reg 1.4 lx in diablo red. lowered and with 17 inch konig alloys | |
| | |
|
|
|
|
|
|
|
Posted: Mon Apr 11, 2011 10:32 am |
|
|
|
|
Joined: Feb 07, 2010
Posts: 5575
Trade Rating: +33
Location: Moscow
|
|
I am sure the rubber bush is part of the shock...
| | |
|
|
|
|
|
|
|
|
|
|
Posted: Mon Apr 11, 2011 10:36 am |
|
|
|
|
Joined: Jul 02, 2010
Posts: 63
Trade Rating: 0
Location: Coventry
|
|
Doesn't sound good then. But thanks for your help
| | |
|
|
|
|
| | |
| W reg 1.4 lx in diablo red. lowered and with 17 inch konig alloys | |
| | |
|
|
|
|
|
|
|
Posted: Mon Apr 11, 2011 10:46 am |
|
|
|
|
Joined: Nov 21, 2010
Posts: 132
Trade Rating: 0
Location: Kettering
|
|
How long's the rear shocks been on? Rear shock bush is quite common, can be caused by fitting issues, i.e. when the mechanic was fitting them, he tightened up the bolts all the way before putting he car on the floor. It causes the bush to rotate in its mounting, its a common issue on most cars with torsion bar suspension.
| | |
|
|
|
|
|
|
|
|
|
|
Posted: Mon Apr 11, 2011 10:50 am |
|
|
|
|
Joined: Feb 09, 2010
Posts: 397
Trade Rating: 0
Location: Stoke on Trent
|
|
you could try and sent the shocker back to the company you got it from they should be able replace the worn bush i had the same problem on my avo rear shocker
| | |
|
|
|
|
|
|
|
|
|
|
Posted: Mon Apr 11, 2011 11:03 am |
|
|
|
|
Joined: Jul 02, 2010
Posts: 63
Trade Rating: 0
Location: Coventry
|
|
its been on for about 2 and a half years now so its defo out of warrenty
| | |
|
|
|
|
| | |
| W reg 1.4 lx in diablo red. lowered and with 17 inch konig alloys | |
| | |
|
|
|
|
|
|
|
Posted: Mon Apr 11, 2011 11:19 am |
|
|
|
|
Joined: Jan 29, 2011
Posts: 6526
Trade Rating: +10
Location: Westhoughton, Lancashire
|
|
You can get a split CV boot kit which you glue along a tongue and groove seam. Saves taking the driveshaft out. I've used them before and never had a problem with them.
| | |
|
|
|
|
|
|
|
|
|
|
Posted: Tue Apr 12, 2011 4:51 am |
|
|
|
|
Joined: Apr 15, 2010
Posts: 514
Trade Rating: +1
Location: Eastbourne
|
|
| macca1411 wrote: |
| You can get a split CV boot kit which you glue along a tongue and groove seam. Saves taking the driveshaft out. I've used them before and never had a problem with them. |
dito about £13 from car parts store
| | |
|
|
|
|
| | |
| *DEAD*206 Gti 138
Toyota Celica T sport 205 BHP | |
| | |
|
|
|
|
|
|
|
Posted: Tue Apr 12, 2011 4:57 am |
|
|
|
|
Joined: Feb 08, 2010
Posts: 5400
Trade Rating: +105
Location: Stafford
|
|
7. Rear brake load sensing valve linkage seized
Just got similar on this today, except mine had fallen off. Was told it was a spring like thing on the rear brake, see if you can unseize it. If not I was told you won't be able to buy one brand new so you would have to buy the whole valve, very expensive.
| | |
|
|
|
|
|
|
|
|
|
|
Posted: Tue Apr 12, 2011 7:48 am |
|
|
|
|
Joined: Jan 22, 2011
Posts: 100
Trade Rating: 0
Location: Earth, most of the time!!
|
|
| macca1411 wrote: |
| You can get a split CV boot kit which you glue along a tongue and groove seam. Saves taking the driveshaft out. I've used them before and never had a problem with them. |
its just insecure, probably the plastic ones just put a new securing strap round it or for simplicity a cable tie 
| | |
|
|
|
|
| | |
| If in doubt, drop a cog and put your foot down | |
| | |
|
|
|
|
|
Membership:
Latest: 
New Today: 0
New Yesterday: 0
Overall: 17129
Online Now [297]:
Visitors: 297
Members: 0
Staff Online Now:
Page Views:
General
Forums Home
Forum FAQ
Search
