|
Author
|
Message |
|
|
 Posted: Mon Sep 19, 2011 2:57 pm |
|
|
|
|
Joined: Apr 21, 2011
Posts: 364
Trade Rating: 0
Location: Notts
|
 |
Never been the best with cars but had a go at removing and swapping my bumper yesterday and got really p**sed off with it, never managed to get it off as couldnt get to the bot/nut or whatever was under the wheel arch.
Whats the best way of getting to it and actually getting the bumper off?
Thanks
| |  |
|
|
 |
|
|
|
|
|
|
Posted: Mon Sep 19, 2011 3:01 pm |
|
|
|
|
Joined: Jul 21, 2011
Posts: 791
Trade Rating: +5
Location: Bourne, Lincs
|
|
|
|
|
 | |  |
| Ford Focus RS in white of course 
filled with all sorts of goodies | |
 | |  |
|
|
|
|
|
|
|
Posted: Mon Sep 19, 2011 3:02 pm |
|
|
|
|
Joined: Feb 07, 2010
Posts: 3828
Trade Rating: +32
|
|
Arch liners out.
And a hacksaw should sort the bolt out
| | |
|
|
|
|
|
|
|
|
|
|
Posted: Mon Sep 19, 2011 3:04 pm |
|
|
|
|
Joined: Feb 07, 2010
Posts: 13077
Trade Rating: +65
Location: England
|
|
Dremel ftw 
| | |
|
|
|
|
|
|
|
|
|
|
Posted: Mon Sep 19, 2011 3:07 pm |
|
|
|
|
Joined: Feb 08, 2010
Posts: 7045
Trade Rating: +5
Location: In the garage
|
|
Buying new nuts and bolts is a good place to start. With some copper grease.
Don't they look nice?
| | |
|
|
|
|
| | |
| 2001 GTi 138, Bilstein Sprint dampers, H&R springs, 21mm Peugeot Sport torsion bars, 22mm rear ARB, Peugeot Sport Group A wishbones, 283mm discs, Goodridge stainless hoses, Maniflow 304 grade 4-2-1 2.5" manifold and system, 200 cell cat, Richard Longman head, 45mm Jenvey throttle bodies, 9.5mm TB spacers, 90mm air horns, Jenvey throttle linkage, Jenvey fuel rail, Aeromotive and Goodridge fuel fittings and braided hose, ITG sausage filter, Radtec custom radiator, Piper Ultimate Road cams, Piper vernier pulleys, Omex 600 ECU. Saxo electric PAS pump, Vibra Technics engine mounts. Samco coolant hoses, TTV steel flywheel, 4.76 final drive ratio, 307 CC 180 ratios. 2019 BMW 530i. 2017 Mercedes C300 convertible. | |
| | |
|
|
|
|
|
|
|
Posted: Mon Sep 19, 2011 3:07 pm |
|
|
|
|
Joined: Sep 12, 2010
Posts: 1912
Trade Rating: +4
Location: Manchester
|
|
get your angryyy on and kick the s**t out of it
if you want it in one piece, undo all the bolts and replace the 2 side ones with proper bolts and big washers, i used wingnuts on mine
| | |
|
|
|
|
|
|
|
|
|
|
Posted: Mon Sep 19, 2011 3:07 pm |
|
|
|
|
Joined: Apr 21, 2011
Posts: 364
Trade Rating: 0
Location: Notts
|
|
| marc206 wrote: |
| http://www.206info.co.uk/Forums/viewtopic/t=3163.html |
Went by that guide to start off with
| | |
|
|
|
|
|
|
|
|
|
|
Posted: Mon Sep 19, 2011 3:11 pm |
|
|
|
|
Joined: Feb 08, 2010
Posts: 7045
Trade Rating: +5
Location: In the garage
|
|
It's often easier to access the nuts from above with the headlights removed.
| | |
|
|
|
|
| | |
| 2001 GTi 138, Bilstein Sprint dampers, H&R springs, 21mm Peugeot Sport torsion bars, 22mm rear ARB, Peugeot Sport Group A wishbones, 283mm discs, Goodridge stainless hoses, Maniflow 304 grade 4-2-1 2.5" manifold and system, 200 cell cat, Richard Longman head, 45mm Jenvey throttle bodies, 9.5mm TB spacers, 90mm air horns, Jenvey throttle linkage, Jenvey fuel rail, Aeromotive and Goodridge fuel fittings and braided hose, ITG sausage filter, Radtec custom radiator, Piper Ultimate Road cams, Piper vernier pulleys, Omex 600 ECU. Saxo electric PAS pump, Vibra Technics engine mounts. Samco coolant hoses, TTV steel flywheel, 4.76 final drive ratio, 307 CC 180 ratios. 2019 BMW 530i. 2017 Mercedes C300 convertible. | |
| | |
|
|
|
|
|
|
|
Posted: Tue Sep 20, 2011 7:52 am |
|
|
|
|
Joined: Nov 27, 2010
Posts: 11520
Trade Rating: +10
Location: What's it to you? ? ?
|
|
| Edward wrote: |
| It's often easier to access the nuts from above with the headlights removed. |
Bumper comes out easy enough with the headlamps still in place.
Small mole grips & torx bit to start the bolt under headlamp, then fingers to spin it out.
| | |
|
|
|
|
|
|
|
|
|
|
Posted: Tue Sep 20, 2011 8:55 am |
|
|
|
|
Joined: Apr 12, 2010
Posts: 116
Trade Rating: 0
Location: Barry, South Wales
|
|
just done mine, work bottom up. use a fork on the arch liner clips, and undo all the bottom screws, arch liners done. take the headlights off and rest them on the engine i found easiest, and make sure you have summat soft underneath to catch it. if your having trouble chances are you've missed a bolt/screw, just follow the edges of the bumper and you should find the little sob.
| | |
|
|
|
|
|
|
|
|
|
|
Posted: Tue Sep 20, 2011 1:05 pm |
|
|
|
|
Joined: Nov 27, 2010
Posts: 11520
Trade Rating: +10
Location: What's it to you? ? ?
|
|
| Dave82517 wrote: |
| take the headlights off and rest them on the engine i found easiest |
Easier to not remove the headlamps as it screws up the beam alignment 
| | |
|
|
|
|
|
|
|
|
|
|
Posted: Tue Sep 20, 2011 1:10 pm |
|
|
|
|
Joined: Feb 07, 2010
Posts: 2800
Trade Rating: +34
Location: Worthing
|
|
| MrBSI wrote: |
| Dave82517 wrote: |
| take the headlights off and rest them on the engine i found easiest |
Easier to not remove the headlamps as it screws up the beam alignment |
Most mot place will re-align them for free, so it's not really the end of the world
And how is it easier not to remove the headlights?
| | |
|
|
|
|
| | |
| Moonstone blue 206 1.4look
pro race 1.2 White
Morettes
GTI wings
TEAM: Carbon Fibre 
TEAM: I'm a greedy jelly fiend! | |
| | |
|
|
|
|
|
|
|
Posted: Tue Sep 20, 2011 1:29 pm |
|
|
|
|
Joined: Feb 08, 2010
Posts: 7045
Trade Rating: +5
Location: In the garage
|
|
| MrBSI wrote: |
| Edward wrote: |
| It's often easier to access the nuts from above with the headlights removed. |
Bumper comes out easy enough with the headlamps still in place.
|
Unless the nut is seized on the bumper bolt.
| | |
|
|
|
|
| | |
| 2001 GTi 138, Bilstein Sprint dampers, H&R springs, 21mm Peugeot Sport torsion bars, 22mm rear ARB, Peugeot Sport Group A wishbones, 283mm discs, Goodridge stainless hoses, Maniflow 304 grade 4-2-1 2.5" manifold and system, 200 cell cat, Richard Longman head, 45mm Jenvey throttle bodies, 9.5mm TB spacers, 90mm air horns, Jenvey throttle linkage, Jenvey fuel rail, Aeromotive and Goodridge fuel fittings and braided hose, ITG sausage filter, Radtec custom radiator, Piper Ultimate Road cams, Piper vernier pulleys, Omex 600 ECU. Saxo electric PAS pump, Vibra Technics engine mounts. Samco coolant hoses, TTV steel flywheel, 4.76 final drive ratio, 307 CC 180 ratios. 2019 BMW 530i. 2017 Mercedes C300 convertible. | |
| | |
|
|
|
|
|
|
|
Posted: Tue Sep 20, 2011 1:45 pm |
|
|
|
|
Joined: Apr 21, 2011
Posts: 364
Trade Rating: 0
Location: Notts
|
|
The nut seems to just turn and turn
| | |
|
|
|
|
|
|
|
|
|
|
Posted: Tue Sep 20, 2011 2:03 pm |
|
|
|
|
Joined: Feb 07, 2010
Posts: 7093
Trade Rating: +11
Location: Suffolk
|
|
If you can, and its been undone a little
Pull the bumper towards you (to the side), that is with all the other bolts undone
It may break, mine didnt, but be warned
Then get a hack saw or molegrips
| | |
|
|
|
|
| | |
| Team Impossible Possible
The only way of finding the limits of the possible is by going beyond them into the impossible - Arthur C. Clarke
Forged 1.6 Turbo
Click to see more
144Bhp @ 7PSi - 193.9Bhp @ 13psi
206 Gti Race Car
Click to see more
For all Race/Track Preparation, Feel Free to PM Me!
Whether its for a custom ratio gearbox or track-day alignment, I can help! | |
| | |
|
|
|
|
|
Membership:
Latest: 
New Today: 0
New Yesterday: 0
Overall: 17130
Online Now [223]:
Visitors: 222
Members: 0
Staff Online Now:
Page Views:
General
Forums Home
Forum FAQ
Search
