|
Author
|
Message |
|
|
 Posted: Wed Feb 08, 2012 4:32 pm |
|
|
|
|
Joined: Feb 09, 2010
Posts: 111
Trade Rating: 0
Location: Coventry
|
 |
can anybody direct me to a thread or site that will talk me through changing a rear quarter
thanks 
| |  |
|
|
 |
|
|
|
|
|
|
Posted: Wed Feb 08, 2012 4:38 pm |
|
|
|
|
Joined: Feb 07, 2010
Posts: 2721
Trade Rating: +6
Location: UK
|
|
Panel? Ive your going to do it, you wouldnt be asking how to. I.E. you will not have th tools/skills. No offense, but its a difficult job.
| | |
|
|
|
|
|
|
|
|
|
|
Posted: Wed Feb 08, 2012 4:48 pm |
|
|
|
|
Joined: Feb 08, 2010
Posts: 10151
Trade Rating: +12
|
|
drill it off and spot weld the new one on, then respray.
sounds easy enough?
i got no idea how it could be done
| | |
|
|
|
|
|
|
|
|
|
|
Posted: Wed Feb 08, 2012 5:55 pm |
|
|
|
|
Joined: Feb 24, 2010
Posts: 2596
Trade Rating: +17
Location: North West Wales
|
|
If your doing it and you have to ask remind me never to get in your car...
| | |
|
|
|
|
|
|
|
|
|
|
Posted: Wed Feb 08, 2012 7:07 pm |
|
|
|
|
Joined: Feb 09, 2010
Posts: 111
Trade Rating: 0
Location: Coventry
|
|
it cant be that hard surely. ive got a spot welder. just found a thread for a cc too
| | |
|
|
|
|
|
|
|
|
|
|
Posted: Wed Feb 08, 2012 7:10 pm |
|
|
|
|
Joined: Feb 24, 2010
Posts: 2596
Trade Rating: +17
Location: North West Wales
|
|
| Elldan wrote: |
| it cant be that hard surely. ive got a spot welder. just found a thread for a cc too |
Your talking about playing around with the whole structure of the body shell. I think it might be a bit harder than what your thinking.
| | |
|
|
|
|
|
|
|
|
|
|
Posted: Thu Feb 09, 2012 5:45 am |
|
|
|
|
Joined: Jan 05, 2011
Posts: 483
Trade Rating: 0
Location: Wiltshire
|
|
actually have some experience in this as before i got my 206, i was getting my civic coupe rear 1/4s done due to heavy rust (in the end i scrapped the car, rusted floorpan  ), i did however watch my mate (a fully qulified wielder/mechanic) when he was working on my car.
1, place new panel against car (mark around the outside so you know where your cutting)
2, check there is nothing structural in the way (support bars, fuel pipes ect)
3, cut out old panel, about 1cm below the line you drew
4, wield in new panel, using a tig/mig wielder (not spot wielded, wont be strong enough, you can spot wield it to keep it in place while you wield it the other way)
5, grind the panel flat
6, fill any remaining gaps/uneven parts
7, sand smooth
8, prime panel
9, sand smooth
10, spray colour of choice
11, laquer panel.
that is just a rough guide, i accept NO responsibilty for you damaging you car or injuring yourself.
if you want an honest oppinion, get a professional to do it, will cost maybe £250 for just the cutting and wielding, also at least it will be done to conform to the structeral regs required.
| | |
|
|
|
|
|
|
|
|
|
|
Posted: Thu Feb 09, 2012 6:09 am |
|
|
|
|
Joined: Feb 08, 2010
Posts: 7045
Trade Rating: +5
Location: In the garage
|
|
Easy. Not.
| | |
|
|
|
|
 | |  |
| 2001 GTi 138, Bilstein Sprint dampers, H&R springs, 21mm Peugeot Sport torsion bars, 22mm rear ARB, Peugeot Sport Group A wishbones, 283mm discs, Goodridge stainless hoses, Maniflow 304 grade 4-2-1 2.5" manifold and system, 200 cell cat, Richard Longman head, 45mm Jenvey throttle bodies, 9.5mm TB spacers, 90mm air horns, Jenvey throttle linkage, Jenvey fuel rail, Aeromotive and Goodridge fuel fittings and braided hose, ITG sausage filter, Radtec custom radiator, Piper Ultimate Road cams, Piper vernier pulleys, Omex 600 ECU. Saxo electric PAS pump, Vibra Technics engine mounts. Samco coolant hoses, TTV steel flywheel, 4.76 final drive ratio, 307 CC 180 ratios. 2019 BMW 530i. 2017 Mercedes C300 convertible. | |
 | |  |
|
|
|
|
|
|
|
Posted: Thu Feb 09, 2012 10:08 am |
|
|
|
|
Joined: Nov 27, 2010
Posts: 11520
Trade Rating: +10
Location: What's it to you? ? ?
|
|
| Elldan wrote: |
| it cant be that hard surely. ive got a spot welder. just found a thread for a cc too |
If you have to ask how to do it then you havent got the skills to make a safe repair 
Im starting to worry about a lot of the questions being asked on here lately, I dread to think how many bodged up & unsafe 206's are driving around after diy repairs have been done! 
| | |
|
|
|
|
| | |
| Toyota C-HR GR Sport 2.0 Hybrid with JBL & Alcantara packs. | |
| | |
|
|
|
|
|
|
|
Posted: Thu Feb 09, 2012 10:11 am |
|
|
|
|
Joined: Feb 10, 2010
Posts: 4014
Trade Rating: +2
|
|
| MrBSI wrote: |
| Elldan wrote: |
| it cant be that hard surely. ive got a spot welder. just found a thread for a cc too |
If you have to ask how to do it then you havent got the skills to make a safe repair
Im starting to worry about a lot of the questions being asked on here lately, I dread to think how many bodged up & unsafe 206's are driving around after diy repairs have been done! |
All of them...remember Peugeot made them
| | |
|
|
|
|
|
|
|
|
|
|
Posted: Thu Feb 09, 2012 12:22 pm |
|
|
|
|
Joined: Feb 07, 2010
Posts: 278
Trade Rating: +3
Location: cleaning the car
|
|
if I was you id let a pro do it dont try and save a couple of quid on something that could jeopardize the safety of you and others common sense really though
| | |
|
|
|
|
|
|
|
|
|
|
Posted: Thu Feb 09, 2012 4:18 pm |
|
|
|
|
Joined: Feb 09, 2010
Posts: 111
Trade Rating: 0
Location: Coventry
|
|
| Nic_206 wrote: |
| if I was you id let a pro do it dont try and save a couple of quid on something that could jeopardize the safety of you and others common sense really though |
amen to that 
some filler and a re-spray will do the job, just thought if it was an easy switch i could put a new one on
| | |
|
|
|
|
|
|
|
|
|
|
Posted: Thu Feb 09, 2012 4:22 pm |
|
|
|
|
Joined: Feb 07, 2010
Posts: 278
Trade Rating: +3
Location: cleaning the car
|
|
what sort of damage is there to your quarter panel im guessing it must be bad if you thought of fitting a new panel?
| | |
|
|
|
|
|
|
|
|
|
|
Posted: Thu Feb 09, 2012 4:30 pm |
|
|
|
|
Joined: Feb 09, 2010
Posts: 111
Trade Rating: 0
Location: Coventry
|
|
its dented the arch and just behind it, its not even too bad was just being tight and fancied the challenge
| | |
|
|
|
|
|
|
|
|
|
|
Posted: Thu Feb 09, 2012 4:35 pm |
|
|
|
|
Joined: Feb 07, 2010
Posts: 278
Trade Rating: +3
Location: cleaning the car
|
|
ahh I get you it would be easyier just to sand fill etc and cheaper, im in the process of sanding the whole car down for a respray atm done the quarter panels quicker then expected too few pics on my project thread
| | |
|
|
|
|
|
|
|
|
Membership:
Latest: 
New Today: 0
New Yesterday: 0
Overall: 17130
Online Now [334]:
Visitors: 333
Members: 0
Staff Online Now:
Page Views:
General
Forums Home
Forum FAQ
Search
