|
Author
|
Message |
|
|
 Posted: Tue Nov 06, 2012 7:37 am |
|
|
|
|
Joined: Nov 06, 2012
Posts: 13
Trade Rating: 0
|
 |
Just joined the forum in hope that someone can help with my misfire!
Trouble codes- P0262 - Injector cylinder 1 circuit, P0201 - Injector Cylinder 1 Circuit.
Ive tried, new plugs (bosch), new coilpack, swapped the injectors about, problem doesnt change cylinder.
Im now guessing its a wiring or ecu fault.
Any suggestions of what could cause this misfire with these codes?
Help appreciated!!
Dan
| |  |
|
|
 |
Last edited by dan106 on Thu Nov 08, 2012 9:37 am; edited 1 time in total
|
|
|
|
|
|
|
Posted: Tue Nov 06, 2012 7:59 am |
|
|
|
|
Joined: Jan 29, 2011
Posts: 6526
Trade Rating: +10
Location: Westhoughton, Lancashire
|
|
More information is needed about the car. We know it's a petrol since you have changed the plugs.
Year and engine would be a help to narrowing down possible causes.
You need to know where injector 1 is for a start. THere is a known fault where the washer jet leaks onto the injector plug.
You're new so it's forgivable as you probably don't realise that there are different variants.
| | |
|
|
|
|
|
|
|
|
|
|
Posted: Tue Nov 06, 2012 8:04 am |
|
|
|
|
Joined: Nov 06, 2012
Posts: 13
Trade Rating: 0
|
|
Its a 1.1 03 plate. Arent peugeots and citroens backwards? So cylinder 1 will be flywheel side?
And yeah i read about that, so i swapped the injectors around, but the fault codes remained at injector 1.
| | |
|
|
|
|
|
|
|
|
|
|
Posted: Tue Nov 06, 2012 8:13 am |
|
|
|
|
Joined: Feb 08, 2010
Posts: 10151
Trade Rating: +12
|
|
yes you are right
cylinder one is gearbox end
| | |
|
|
|
|
|
|
|
|
|
|
Posted: Tue Nov 06, 2012 8:17 am |
|
|
|
|
Joined: Jan 29, 2011
Posts: 6526
Trade Rating: +10
Location: Westhoughton, Lancashire
|
|
Yep, you're spot on with them being backward. The codes are generic so depending on the code reader software, it may get confused with number 4.
After doing what you have already done, I'd be looking at the wiring to make sure there are no shorts or bad connections.
Did you clear the codes after swapping everything about to make sure it wasn't a stored code you were looking at?
| | |
|
|
|
|
|
|
|
|
|
|
Posted: Tue Nov 06, 2012 8:21 am |
|
|
|
|
Joined: Nov 06, 2012
Posts: 13
Trade Rating: 0
|
|
Im using a snap on ethos, cleared codes everytime, ive spoke to a mate who works at peugeot, he said there is a common fault with the wiring to the injectors, but because mine has a rubber like coating its the revised version? I couldnt see anything wrong with the wiring, is there a way to check it using a multimetre?
| | |
|
|
|
|
|
|
|
|
|
|
Posted: Tue Nov 06, 2012 9:06 am |
|
|
|
|
Joined: Feb 08, 2010
Posts: 10151
Trade Rating: +12
|
|
check the injector voltage while cranking; it should be around 12v
or use a noid light
| | |
|
|
|
|
|
|
|
|
|
|
Posted: Tue Nov 06, 2012 10:13 am |
|
|
|
|
Joined: Nov 06, 2012
Posts: 13
Trade Rating: 0
|
|
so unplug the injector and test the plug?
| | |
|
|
|
|
|
|
|
|
|
|
Posted: Tue Nov 06, 2012 11:03 am |
|
|
|
|
Joined: Nov 06, 2012
Posts: 13
Trade Rating: 0
|
|
Right just turned it over with th injectors out, closest injector to the cambelt not firing, swapped injectors and its still the same one not firing
| | |
|
|
|
|
|
|
|
|
|
|
Posted: Tue Nov 06, 2012 11:26 am |
|
|
|
|
Joined: Feb 07, 2010
Posts: 2949
Trade Rating: +6
Location: Athens, Greece
|
|
That's #4.
Info-flash from Peugeot says that #4 get's dribbled-on by the hole where the RHS windscreen squirter fits.
They recomend replacing injector connector harness IIRC.
If this doesn't fix it, maybe ECU or ECU-connector.
| | |
|
|
|
|
 | |  |
| 1.4i, 2001, 3-door, China Blue
Repair safely - Drive safely | |
 | |  |
|
|
|
|
|
|
|
Posted: Thu Nov 08, 2012 5:07 am |
|
|
|
|
Joined: Nov 06, 2012
Posts: 13
Trade Rating: 0
|
|
Is there anything else it might be? just that wiring harness is 106+vat, i dont have that much money spare!
| | |
|
|
|
|
|
|
|
|
|
|
Posted: Thu Nov 08, 2012 7:16 am |
|
|
|
|
Joined: Nov 06, 2012
Posts: 13
Trade Rating: 0
|
|
Is the wiring harness for the injectors the same on different models? the nearest scrappy to me doesnt have any 1.1s and i need to know before i pay for a lift up there to find its different!
Help please i need my car back!
| | |
|
|
|
|
|
|
|
|
|
|
Posted: Thu Nov 08, 2012 9:36 am |
|
|
|
|
Joined: Nov 06, 2012
Posts: 13
Trade Rating: 0
|
|
Went to the scrappy anyway, changed the wiring harness, no difference, codes cleared before start up and the exact same codes after start up.
Gotta be ecu hasnt it???
| | |
|
|
|
|
|
|
|
|
|
|
Posted: Thu Nov 08, 2012 11:50 am |
|
|
|
|
Joined: Feb 07, 2010
Posts: 2949
Trade Rating: +6
Location: Athens, Greece
|
|
More and more likely now.
Did you plug-unplug the ECU connector(s) a couple of times?
Don't use spray on them thgough, and disconnect battery properly first.
| | |
|
|
|
|
| | |
| 1.4i, 2001, 3-door, China Blue
Repair safely - Drive safely | |
| | |
|
|
|
|
|
|
|
Posted: Mon Nov 26, 2012 6:50 am |
|
|
|
|
Joined: Nov 06, 2012
Posts: 13
Trade Rating: 0
|
|
Im back, car is still not sorted, eevn tried new ecu!!
| | |
|
|
|
|
|
|
|
|
Membership:
Latest: 
New Today: 0
New Yesterday: 0
Overall: 17129
Online Now [360]:
Visitors: 359
Members: 0
Staff Online Now:
Page Views:
General
Forums Home
Forum FAQ
Search
