|
Author
|
Message |
|
|
 Posted: Thu Jan 31, 2013 1:41 pm |
|
|
|
|
Joined: Jan 31, 2013
Posts: 5
Trade Rating: 0
|
 |
Sunday morning had dashboard message saying top up cooling fluid. Was slightly worried but didn't think to much, of it and topped it up. Just suspected I had let it run a bit low.
Yesterday night (Wednesday) had the same message while driving and telling me to stop the engine. Upon checking the reservoir was empty and I noticed water coming out of a blue cap to the side of the engine. I have a photo but cant see an option to upload one.
Anyone got any suggestions to the cause and solution.
Peugeot 206 2.0 HDI Sport, 2005.
Cheers.
| |  |
|
|
 |
|
|
|
|
|
|
Posted: Thu Jan 31, 2013 1:57 pm |
|
|
|
|
Joined: Jun 08, 2010
Posts: 1035
Trade Rating: +17
Location: North Manchester
|
|
if you mean this
its one of 2 bleed points , its basicly just a dust cap so you could take one off a wheel and put it in its place to see if it stops the leak
| | |
|
|
|
|
|
|
|
|
|
|
Posted: Thu Jan 31, 2013 2:16 pm |
|
|
|
|
Joined: Jan 31, 2013
Posts: 5
Trade Rating: 0
|
|
Thanks.
Thats exactly the one.
If it is a bleed point and its spraying out would I be right in assuming its because there is to much pressure or can it literally just be a faulty valve?
No other signs or faults, engine temperature was not unusually high either.
| | |
|
|
|
|
|
|
|
|
|
|
Posted: Thu Jan 31, 2013 2:33 pm |
|
|
|
|
Joined: Feb 08, 2010
Posts: 10151
Trade Rating: +12
|
|
could just be leaking
| | |
|
|
|
|
|
|
|
|
|
|
Posted: Thu Jan 31, 2013 3:05 pm |
|
|
|
|
Joined: Feb 10, 2010
Posts: 4266
Trade Rating: +4
Location: Palestine
|
|
fix it asap so u don't damage the engine with no coolant run inside.this is the thermostat housing,and it got bleeding point,so if it's cracker where the blue cap fits,you will have to replace it.
| | |
|
|
|
|
|
|
|
|
|
|
Posted: Fri Feb 01, 2013 4:04 am |
|
|
|
|
Joined: Jan 31, 2013
Posts: 5
Trade Rating: 0
|
|
Thanks very much. Going to take a look at it tomorrow and hopefully find the cause.
| | |
|
|
|
|
|
|
|
|
|
|
Posted: Fri Feb 01, 2013 6:43 am |
|
|
|
|
Joined: Feb 08, 2010
Posts: 7045
Trade Rating: +5
Location: In the garage
|
|
Changing the dust cap won't fix anything!
| | |
|
|
|
|
 | |  |
| 2001 GTi 138, Bilstein Sprint dampers, H&R springs, 21mm Peugeot Sport torsion bars, 22mm rear ARB, Peugeot Sport Group A wishbones, 283mm discs, Goodridge stainless hoses, Maniflow 304 grade 4-2-1 2.5" manifold and system, 200 cell cat, Richard Longman head, 45mm Jenvey throttle bodies, 9.5mm TB spacers, 90mm air horns, Jenvey throttle linkage, Jenvey fuel rail, Aeromotive and Goodridge fuel fittings and braided hose, ITG sausage filter, Radtec custom radiator, Piper Ultimate Road cams, Piper vernier pulleys, Omex 600 ECU. Saxo electric PAS pump, Vibra Technics engine mounts. Samco coolant hoses, TTV steel flywheel, 4.76 final drive ratio, 307 CC 180 ratios. 2019 BMW 530i. 2017 Mercedes C300 convertible. | |
 | |  |
|
|
|
|
|
|
|
Posted: Fri Feb 01, 2013 7:45 am |
|
|
|
|
Joined: Jan 31, 2013
Posts: 5
Trade Rating: 0
|
|
probably not, but now I know it can be taken off without damaging anything it will allow me to look for the cause and in turn a solution.
| | |
|
|
|
|
|
|
|
|
|
|
Posted: Mon Feb 04, 2013 6:22 am |
|
|
|
|
Joined: Jan 31, 2013
Posts: 5
Trade Rating: 0
|
|
While changing the dust cap would not quite have fixed it, it was not far off.
The rubber mounts from the plastic engine cover had broke causing movement. It had hit the dust cap and caused a small crack. Could have fixed it with super glue but I went and got a replacement thermostat cover to be safe.
Thanks for your help.
| | |
|
|
|
|
|
|
|
|
|
|
Posted: Thu Feb 14, 2013 1:49 pm |
|
|
|
|
Joined: Feb 10, 2010
Posts: 4266
Trade Rating: +4
Location: Palestine
|
|
it's good that you got it fixed,a new thermostat cover is the best fix 
| | |
|
|
|
|
|
|
|
|
Membership:
Latest: 
New Today: 0
New Yesterday: 0
Overall: 17130
Online Now [194]:
Visitors: 193
Members: 0
Staff Online Now:
Page Views:
General
Forums Home
Forum FAQ
Search
