|
Author
|
Message |
|
|
 Posted: Thu Apr 25, 2013 6:22 pm |
|
|
|
|
Joined: Feb 08, 2010
Posts: 106
Trade Rating: 0
Location: Aberdeenshire
|
 |
evening
whats people's opinions on the easiest method to put a gti engine back into car? i'll be test fitting gearbox to make sure clutchplate is lined up beforehand.
it would be easier to join them outwith car but previous experience taking them out together it was pretty awkward - had to pivot/twist to get it out complete and still scratched the shell
any thoughts?
*edit and i dont have a car lift, so no chance of going in from the bottom
| |  |
|
|
 |
|
|
|
|
|
|
Posted: Fri Apr 26, 2013 1:06 am |
|
|
|
|
Joined: Feb 07, 2010
Posts: 2719
Trade Rating: +6
Location: UK
|
|
I'm doing this in the summer, Haynes manual says you can do it with box attached, would make life easier of it did!
| | |
|
|
|
|
|
|
|
|
|
|
Posted: Fri Apr 26, 2013 1:59 am |
|
|
|
|
Joined: Feb 07, 2010
Posts: 4117
Trade Rating: +25
Location: No Man's Land
|
|
If your engine is out why not just strip your front end down and then that way you can just slot it into place with very little chance of scratching the shell.
Easiest way ive found when removing and engine and you can slot it into place in 1 piece.
| | |
|
|
|
|
|
|
|
|
|
|
Posted: Fri Apr 26, 2013 2:03 am |
|
|
|
|
Joined: Feb 08, 2010
Posts: 7045
Trade Rating: +5
Location: In the garage
|
|
Put engine and gearbox back in together from underneath. Much less messing.
| | |
|
|
|
|
 | |  |
| 2001 GTi 138, Bilstein Sprint dampers, H&R springs, 21mm Peugeot Sport torsion bars, 22mm rear ARB, Peugeot Sport Group A wishbones, 283mm discs, Goodridge stainless hoses, Maniflow 304 grade 4-2-1 2.5" manifold and system, 200 cell cat, Richard Longman head, 45mm Jenvey throttle bodies, 9.5mm TB spacers, 90mm air horns, Jenvey throttle linkage, Jenvey fuel rail, Aeromotive and Goodridge fuel fittings and braided hose, ITG sausage filter, Radtec custom radiator, Piper Ultimate Road cams, Piper vernier pulleys, Omex 600 ECU. Saxo electric PAS pump, Vibra Technics engine mounts. Samco coolant hoses, TTV steel flywheel, 4.76 final drive ratio, 307 CC 180 ratios. 2019 BMW 530i. 2017 Mercedes C300 convertible. | |
 | |  |
|
|
|
|
|
|
|
Posted: Fri Apr 26, 2013 6:49 am |
|
|
|
|
Joined: Feb 08, 2010
Posts: 106
Trade Rating: 0
Location: Aberdeenshire
|
|
thanks for the responses.
in regards to what the haynes says, i'd agree its possible but how easy...
front end is stripped uz, just the lower front crossmember left. would you put in sideways and twist from there?
Any suggestions on getting the height Paul to go from underneath?
| | |
|
|
|
|
|
|
|
|
|
|
Posted: Fri Apr 26, 2013 2:13 pm |
|
|
|
|
Joined: Feb 10, 2010
Posts: 4266
Trade Rating: +4
Location: Palestine
|
|
| Edward wrote: |
| Put engine and gearbox back in together from underneath. Much less messing. |
 
| | |
|
|
|
|
|
|
|
|
|
|
Posted: Fri Apr 26, 2013 10:48 pm |
|
|
|
|
Joined: Nov 08, 2011
Posts: 141
Trade Rating: 0
Location: Trinidad and Tobago
|
|
under is easiest just drop the subframe
| | |
|
|
|
|
| | |
| GTi 180 Obsidian Black
SW 1.6 16v Sahara Yellow | |
| | |
|
|
|
|
|
Membership:
Latest: 
New Today: 0
New Yesterday: 0
Overall: 17129
Online Now [130]:
Visitors: 129
Members: 0
Staff Online Now:
Page Views:
General
Forums Home
Forum FAQ
Search
