|
Author
|
Message |
|
|
 Posted: Fri May 03, 2013 5:27 pm |
|
|
|
|
Joined: Feb 19, 2013
Posts: 207
Trade Rating: +5
Location: stirling
|
 |
my 180 twin horn sounds like its underwater, is it possible to chop and change without removing the front bumper?
any help is appreciated 
| |  |
|
|
 |
|
|
|
|
|
|
Posted: Fri May 03, 2013 5:57 pm |
|
|
|
|
Joined: Feb 24, 2010
Posts: 2596
Trade Rating: +17
Location: North West Wales
|
|
Depends how many cuts you want on your hands, it's possible but not straight forward.
| | |
|
|
|
|
|
|
|
|
|
|
Posted: Fri May 03, 2013 6:22 pm |
|
|
|
|
Joined: Aug 07, 2010
Posts: 247
Trade Rating: +1
Location: Ash, Surrey
|
|
?? Is it not the same as the horn on any other 206? They're abit fiddly to get out but just jack up the car and get in with a sprocket wrench.. will take 5-10 minutes of fiddling with the one little screw but it comes off eventually. When I changed mine I had to strip the wires and remember nearly dropping a scalpel in my eye when I knocked my arm.. just ended up with a stabbed cheek luckily 
| | |
|
|
|
|
|
|
|
|
|
|
Posted: Fri May 03, 2013 7:38 pm |
|
|
|
|
Joined: Feb 19, 2013
Posts: 207
Trade Rating: +5
Location: stirling
|
|
yikes (about the scalpel) well i may end up just removing the bumper, better than making an easy job difficult
| | |
|
|
|
|
|
|
|
|
|
|
Posted: Sat May 04, 2013 3:56 am |
|
|
|
|
Joined: Aug 07, 2010
Posts: 247
Trade Rating: +1
Location: Ash, Surrey
|
|
seriously, if it's the same as mine was there's no point going to all the effort of removing the bumper! That seems like a whole lot of effort for one little screw holding the horn. once that's off there's just a little clip for the wiring, you pull out the metal bit in that and the horns off.. Want me to take mine off this morning to show you a few pics of what I mean?
as for the scalpel.. it's really not a dangerous job. I just have a habit of rushing because I'm an impatient git.. it's a safe, easy job honest  You shouldn't have to strip any wires either. My horn wasn't working because the wiring had snapped from what I remember so I had to strip the wire to pop it back in.
| | |
|
|
|
|
|
|
|
|
|
|
Posted: Sat May 04, 2013 4:38 am |
|
|
|
|
Joined: Feb 19, 2013
Posts: 207
Trade Rating: +5
Location: stirling
|
|
its fine, i know where it is lol. its the twin horn setup on the 180, i dont think urs has that 1, bearing in mind the engine bay in the 180 is jam packed and the 1.4's arent
| | |
|
|
|
|
|
|
|
|
|
|
Posted: Sat May 04, 2013 4:55 am |
|
|
|
|
Joined: Aug 07, 2010
Posts: 247
Trade Rating: +1
Location: Ash, Surrey
|
|
yeh true. The horn on mine is still behind the front bumper but might be in a different place, and yeh it's not a twin horn. good luck with getting it out all the same, hope it's no trouble!
| | |
|
|
|
|
|
|
|
|
|
|
Posted: Sat May 04, 2013 10:03 am |
|
|
|
|
Joined: Feb 19, 2013
Posts: 207
Trade Rating: +5
Location: stirling
|
|
thanks mate, i'll let u know how i get on
| | |
|
|
|
|
|
|
|
|
Membership:
Latest: 
New Today: 0
New Yesterday: 0
Overall: 17129
Online Now [226]:
Visitors: 225
Members: 0
Staff Online Now:
Page Views:
General
Forums Home
Forum FAQ
Search
