|
Author
|
Message |
|
|
 Posted: Thu Apr 02, 2015 3:50 pm |
|
|
|
|
Joined: Feb 07, 2010
Posts: 729
Trade Rating: 0
Location: Norfolk
|
 |
This washer goes between the oil cooler, further up.
I wonder if I replace it if it needs to be torqued up?
Thanks
| |  |
|
|
 |
|
|
|
|
|
|
Posted: Fri Apr 03, 2015 3:42 am |
|
|
|
|
Joined: Feb 10, 2010
Posts: 4266
Trade Rating: +4
Location: Palestine
|
|
Well done 
| | |
|
|
|
|
|
|
|
|
|
|
Posted: Fri Apr 03, 2015 2:29 pm |
|
|
|
|
Joined: Feb 08, 2010
Posts: 526
Trade Rating: 0
Location: Italy
|
|
Nevermind, I tried all the things, I changed 3 gaskets, I torqued it up, down, no way. After a week the oil leak comes back.
| | |
|
|
|
|
 | |  |
| Silver grey RC|Pug Sport remap|Group A induction|Supersprint backbox|lower strut bar|RCCup wishbones|Eibach Pro-Street-S|302mm brakes+23.8 master cylinder|Vibra Technics|Quaife LSD|Cupra R splitter|modded bonnet vent|black Valeos|207i tail lights|Chromed rear foglight|Bi-xenon 6000k+all led (in+out)|406 rear mirror | |
 | |  |
|
|
|
|
|
|
|
Posted: Fri Apr 03, 2015 3:58 pm |
|
|
|
|
Joined: Jul 13, 2010
Posts: 1032
Trade Rating: +10
Location: sutton surrey/welwyn garden city
|
|
Wash the oil off with a jet wash and then recheck after a drive to see where it's coming from
| | |
|
|
|
|
| | |
| You never really learn to swear until you learn to drive | |
| | |
|
|
|
|
|
|
|
Posted: Tue Apr 07, 2015 6:01 pm |
|
|
|
|
Joined: Feb 07, 2010
Posts: 729
Trade Rating: 0
Location: Norfolk
|
|
Shall hopefully be getting my new washer Thursday. When refitting is the a torque setting for the big bolt that screws through the oil cooler?
| | |
|
|
|
|
|
|
|
|
|
|
Posted: Wed Apr 08, 2015 7:11 am |
|
|
|
|
Joined: Feb 10, 2010
Posts: 174
Trade Rating: 0
Location: London
|
|
| mattymj wrote: |
| Shall hopefully be getting my new washer Thursday. When refitting is the a torque setting for the big bolt that screws through the oil cooler? |
I would imagine there is considering there is a gasket behind it. Try it as hand tight plus a quarter turn and see from there, most rubber seals will be crushed beyond this point.
| | |
|
|
|
|
| | |
| Black 206 Gti. Soon to be 2.2 | |
| | |
|
|
|
|
|
|
|
Posted: Wed Apr 08, 2015 1:23 pm |
|
|
|
|
Joined: Feb 07, 2010
Posts: 2719
Trade Rating: +6
Location: UK
|
|
Would it hurt to put sump sealant on the outer edges?
| | |
|
|
|
|
|
|
|
|
|
|
Posted: Thu Apr 09, 2015 8:38 am |
|
|
|
|
Joined: Feb 07, 2010
Posts: 729
Trade Rating: 0
Location: Norfolk
|
|
I have the new seal. Peugeot state a 8 nm tightening! Isn't that hand tight?
| | |
|
|
|
|
|
|
|
|
|
|
Posted: Thu Apr 09, 2015 8:48 am |
|
|
|
|
Joined: Feb 10, 2010
Posts: 174
Trade Rating: 0
Location: London
|
|
| mattymj wrote: |
| I have the new seal. Peugeot state a 8 nm tightening! Isn't that hand tight? |
Without a torque wrench its hard to say
| | |
|
|
|
|
| | |
| Black 206 Gti. Soon to be 2.2 | |
| | |
|
|
|
|
|
|
|
Posted: Thu Apr 09, 2015 8:57 am |
|
|
|
|
Joined: Feb 07, 2010
Posts: 729
Trade Rating: 0
Location: Norfolk
|
|
Could go for hand tight plus a 1/4 turn!
| | |
|
|
|
|
|
|
|
|
|
|
Posted: Thu Apr 09, 2015 10:38 am |
|
|
|
|
Joined: Feb 07, 2010
Posts: 729
Trade Rating: 0
Location: Norfolk
|
|
Not too much difference
| | |
|
|
|
|
|
|
|
|
|
|
Posted: Thu Apr 09, 2015 12:13 pm |
|
|
|
|
Joined: Feb 07, 2010
Posts: 729
Trade Rating: 0
Location: Norfolk
|
|
I found the cooler had lines on it so I hand tightened it then aligned it square
| | |
|
|
|
|
|
|
|
|
|
|
Posted: Fri Apr 10, 2015 9:02 am |
|
|
|
|
Joined: Apr 01, 2014
Posts: 668
Trade Rating: 0
Location: Cornwall
|
|
| Steve206 wrote: |
| Would it hurt to put sump sealant on the outer edges? |
Shoot me
| | |
|
|
|
|
| | |
| If it aint broke dont fix it ! | |
| | |
|
|
|
|
|
|
|
Posted: Fri Apr 10, 2015 9:25 am |
|
|
|
|
Joined: Feb 07, 2010
Posts: 2719
Trade Rating: +6
Location: UK
|
|
?
| | |
|
|
|
|
|
|
|
|
|
|
Posted: Fri Apr 10, 2015 2:15 pm |
|
|
|
|
Joined: Apr 24, 2013
Posts: 267
Trade Rating: +1
Location: Near Portsmouth
|
|
So did it sort your leak?
| | |
|
|
|
|
|
|
|
|
Membership:
Latest: 
New Today: 0
New Yesterday: 0
Overall: 17129
Online Now [73]:
Visitors: 72
Members: 0
Staff Online Now:
Page Views:
General
Forums Home
Forum FAQ
Search
