|
Author
|
Message |
|
|
 Posted: Fri Sep 30, 2016 6:37 pm |
|
|
|
|
Joined: Sep 30, 2016
Posts: 3
Trade Rating: 0
|
 |
Got a really bad problem I can't solve on a peugot 206cc 2002 Y reg. High beam is fine. All other lights too. Just left side low beam headlight don't work.
Changed bulb H7 even if i thought old one was allright. Checked all fuses one by one looks allright.
Any ideas how to solve this?
Thanks
| |  |
|
|
 |
|
|
|
|
|
|
Posted: Fri Sep 30, 2016 9:31 pm |
|
|
|
|
Joined: Jan 29, 2011
Posts: 6526
Trade Rating: +10
Location: Westhoughton, Lancashire
|
|
Always worth checking fuses with a continuity tester rather than by eye as sometimes they can look alright but have blown.
Did you check the engine bay fuses (F11) as well as the ones under the steering wheel?
If F11 is OK then you'll need to crack out the multimeter and start checking the feed to and from the plug to rule out a bad connection.
| | |
|
|
|
|
|
|
|
|
|
|
Posted: Sat Oct 01, 2016 5:42 am |
|
|
|
|
Joined: Feb 08, 2010
Posts: 7045
Trade Rating: +5
Location: In the garage
|
|
I'd get a multimeter straight on the headlamp plug terminal to check for power.
| | |
|
|
|
|
 | |  |
| 2001 GTi 138, Bilstein Sprint dampers, H&R springs, 21mm Peugeot Sport torsion bars, 22mm rear ARB, Peugeot Sport Group A wishbones, 283mm discs, Goodridge stainless hoses, Maniflow 304 grade 4-2-1 2.5" manifold and system, 200 cell cat, Richard Longman head, 45mm Jenvey throttle bodies, 9.5mm TB spacers, 90mm air horns, Jenvey throttle linkage, Jenvey fuel rail, Aeromotive and Goodridge fuel fittings and braided hose, ITG sausage filter, Radtec custom radiator, Piper Ultimate Road cams, Piper vernier pulleys, Omex 600 ECU. Saxo electric PAS pump, Vibra Technics engine mounts. Samco coolant hoses, TTV steel flywheel, 4.76 final drive ratio, 307 CC 180 ratios. 2019 BMW 530i. 2017 Mercedes C300 convertible. | |
 | |  |
|
|
|
|
|
|
|
Posted: Sat Oct 01, 2016 6:20 am |
|
|
|
|
Joined: Sep 30, 2016
Posts: 3
Trade Rating: 0
|
|
it seems power coming to red wire terminal but not to black wire one.
| | |
|
|
|
|
|
|
|
|
|
|
Posted: Sat Oct 01, 2016 6:39 am |
|
|
|
|
Joined: Apr 14, 2010
Posts: 713
Trade Rating: +2
Location: Gothenburg, Sweden
|
|
| dedemiegas wrote: |
| it seems power coming to red wire terminal but not to black wire one. |
You need +12 on one side (red) and a connection to ground on the other (set meter to resistance [or continuity beep] and check for good connection to ground/battery negative pole.) Don't probe the red while on resistance/continuity - might let the magic smoke out of the meter 
Or on voltage, just measure the voltage between the two terminals in the plug.
If you get 12-14V across those but a known good bulb still doesn't light up, you might have a high resistance/poor connection somewhere. The meter draws very little current, therefore the voltage drop across the poor connection is negligible and you still see 12-14 at the plug, but the bulb draws a much bigger current, causing a big voltage drop across the poor connection, not leaving enough voltage across /current flowing through the bulb for it to light up.
You could try setting the meter to 10/20A range, stick one terminal of the bulb into the plug and connect the meter between the empty connector in the plug and the unconnected terminal of the bulb and see if there is any current at all flowing.
| | |
|
|
|
|
| | |
| Silvermetallic 2004 206 RC | |
| | |
|
|
|
|
|
|
|
Posted: Sat Oct 01, 2016 3:09 pm |
|
|
|
|
Joined: Sep 30, 2016
Posts: 3
Trade Rating: 0
|
|
So my tester was wrong. It was no power in terminal. I checked all fuses under the steering wheel aswell. They was ok. So I bought new fuses and replaced them that's pic how it looks, am I looking to right ones?
www.happygiftbaskets.c...334[1].jpg
And if fuses ok but no power in terminals what next step to sort out problem? I'm confused.
Thank you
| | |
|
|
|
|
|
|
|
|
|
|
Posted: Mon Oct 03, 2016 11:58 am |
|
|
|
|
Joined: Feb 10, 2010
Posts: 4266
Trade Rating: +4
Location: Palestine
|
|
usually the fuses concern the headlight are located in the engine box,not under the steering wheel.
| | |
|
|
|
|
|
|
|
|
|
|
Posted: Thu Nov 10, 2016 7:01 pm |
|
|
|
|
Joined: Nov 10, 2016
Posts: 2
Trade Rating: 0
|
|
Hi new on here. My front passenger dipped beam light is not working. Changed the bulb but no difference. Next step is to change the fuse. Might sound a silly question, but are the 206 fuses standard or mini blade fuses?
| | |
|
|
|
|
|
|
|
|
|
|
Posted: Fri Nov 11, 2016 1:23 pm |
|
|
|
|
Joined: Apr 14, 2010
Posts: 713
Trade Rating: +2
Location: Gothenburg, Sweden
|
|
| GV59 wrote: |
| Hi new on here. My front passenger dipped beam light is not working. Changed the bulb but no difference. Next step is to change the fuse. Might sound a silly question, but are the 206 fuses standard or mini blade fuses? |
Mixed (both)
GIYF
Engine compartment fusebox
Passenger compartment fusebox
Might not exactly match yours depending on preplex or multiplexed wiring system (switches in 2001)
| | |
|
|
|
|
| | |
| Silvermetallic 2004 206 RC | |
| | |
|
|
|
|
|
Membership:
Latest: 
New Today: 0
New Yesterday: 0
Overall: 17130
Online Now [294]:
Visitors: 293
Members: 0
Staff Online Now:
Page Views:
General
Forums Home
Forum FAQ
Search
