 |
 General Info Goodies Search Web Stats Members
 Donations
|
|
|
|
|
 |
|
Forums › The Car › 206 Problems › Temp goes through the roof & no a/c now |
|
 |
 |
 |
 |
|
Author
|
Message |
|
|
 Posted: Sun Apr 01, 2012 1:33 am |
|
|
|
|
Joined: Apr 01, 2012
Posts: 14
Trade Rating: 0
Location: Walsall
|
 |
Hi guys great job your doing with the forum, been reading a lot of info on here and it's been very interesting. I have a problem and was wondering if you guys could help. The misses and I brought a 206 recently and on a journey the other day the temp went through the roof and eventually the engine light come on. So stopped and waited until it cooled down, we was stuck in traffic. I can't hear the fan kicking in, and also the a/c has stopped working just blows hot air. It did work when we brought the car. But to keep temp down in traffic have to have the heaters full on hot which cooks me in this hot weather, I was wondering if you guys had any info? If you need more to go on then please ask and I will try my best, it's a 1.4 8v on a v plate. 1991. Also where the pipe attaches to the coolant bottle the clip has come off so the hose is jut pushed on, but it hasn't leaked only once or when temp goes above 100. But I top it up and it lowers abit. Sits at about 90 while on motorway or driving constantly but don't like sitting in traffic and rises really quickly. Thanks guys and info would be much appreciated
Dan
| |  |
|
|
 |
 | |  |
| Why do we bother with French cars! I just keep buying them. | |
 | |  |
|
|
|
|
|
|
|
Posted: Sun Apr 01, 2012 2:00 am |
|
|
|
|
Joined: Feb 07, 2010
Posts: 5574
Trade Rating: +11
Location: UK
|
|
|
|
|
|
|
|
|
|
|
Posted: Sun Apr 01, 2012 3:36 am |
|
|
|
|
Joined: Apr 01, 2012
Posts: 14
Trade Rating: 0
Location: Walsall
|
|
Cheers will give it ago, just a pain in the a**e that you have to remove bumper.
| | |
|
|
|
|
| | |
| Why do we bother with French cars! I just keep buying them. | |
| | |
|
|
|
|
|
|
|
Posted: Sun Apr 01, 2012 3:40 am |
|
|
|
|
Joined: Feb 07, 2010
Posts: 5574
Trade Rating: +11
Location: UK
|
|
Na you can access the area without removing the whole bumper. Just remove the top grill area above the bumper/under the lights. 
this description helped me also:
www.petercoopercarrepa..._fan_w.htm
| | |
|
|
|
|
|
|
|
|
|
|
Posted: Sun Apr 01, 2012 3:55 am |
|
|
|
|
Joined: Feb 08, 2010
Posts: 7045
Trade Rating: +5
Location: In the garage
|
|
You can check the relay connections with the bumper in place. If anything needs fixing it's easier if you remove the bumper.
| | |
|
|
|
|
| | |
| 2001 GTi 138, Bilstein Sprint dampers, H&R springs, 21mm Peugeot Sport torsion bars, 22mm rear ARB, Peugeot Sport Group A wishbones, 283mm discs, Goodridge stainless hoses, Maniflow 304 grade 4-2-1 2.5" manifold and system, 200 cell cat, Richard Longman head, 45mm Jenvey throttle bodies, 9.5mm TB spacers, 90mm air horns, Jenvey throttle linkage, Jenvey fuel rail, Aeromotive and Goodridge fuel fittings and braided hose, ITG sausage filter, Radtec custom radiator, Piper Ultimate Road cams, Piper vernier pulleys, Omex 600 ECU. Saxo electric PAS pump, Vibra Technics engine mounts. Samco coolant hoses, TTV steel flywheel, 4.76 final drive ratio, 307 CC 180 ratios. 2019 BMW 530i. 2017 Mercedes C300 convertible. | |
| | |
|
|
|
|
|
|
|
Posted: Sun Apr 01, 2012 4:08 am |
|
|
|
|
Joined: Nov 27, 2010
Posts: 11520
Trade Rating: +10
Location: What's it to you? ? ?
|
|
| Dannyskittles wrote: |
| just a pain in the a**e that you have to remove bumper. |
Front bumper takes less then 5 minutes to remove on a 206 with the right tools.
| | |
|
|
|
|
| | |
| Toyota C-HR GR Sport 2.0 Hybrid with JBL & Alcantara packs. | |
| | |
|
|
|
|
|
|
|
Posted: Sun Apr 01, 2012 4:22 am |
|
|
|
|
Joined: Feb 08, 2010
Posts: 7045
Trade Rating: +5
Location: In the garage
|
|
If the bolts on the wings aren't seized...
| | |
|
|
|
|
| | |
| 2001 GTi 138, Bilstein Sprint dampers, H&R springs, 21mm Peugeot Sport torsion bars, 22mm rear ARB, Peugeot Sport Group A wishbones, 283mm discs, Goodridge stainless hoses, Maniflow 304 grade 4-2-1 2.5" manifold and system, 200 cell cat, Richard Longman head, 45mm Jenvey throttle bodies, 9.5mm TB spacers, 90mm air horns, Jenvey throttle linkage, Jenvey fuel rail, Aeromotive and Goodridge fuel fittings and braided hose, ITG sausage filter, Radtec custom radiator, Piper Ultimate Road cams, Piper vernier pulleys, Omex 600 ECU. Saxo electric PAS pump, Vibra Technics engine mounts. Samco coolant hoses, TTV steel flywheel, 4.76 final drive ratio, 307 CC 180 ratios. 2019 BMW 530i. 2017 Mercedes C300 convertible. | |
| | |
|
|
|
|
|
|
|
Posted: Sun Apr 01, 2012 5:27 am |
|
|
|
|
Joined: Apr 01, 2012
Posts: 14
Trade Rating: 0
Location: Walsall
|
|
Everything on this car is seized lol. Well I'll put it on some axle stands and have a look. See if I can see anything and then start removing anything in my way great help so far cheers guys
| | |
|
|
|
|
| | |
| Why do we bother with French cars! I just keep buying them. | |
| | |
|
|
|
|
|
|
|
Posted: Sun Apr 01, 2012 6:29 am |
|
|
|
|
Joined: Mar 12, 2011
Posts: 3
Trade Rating: 0
Location: Midlands
|
|
Had some problems with my 206 and overheating when I brought it. I knew this to be the case at the time of purchasing and was prepared to fix it all the way to the head gasket if necessary as the condition of the car was worth the work. Bloody bargain it was too LOL.
First point of checking for us was the fan and we found that all the wiring concerned with the fan was corroded and crumbled when disturbed so be prepared to have to extend and replace wires / connections.
We ended up using male and female bullet connectors to extend broken wires and spade connector females to make new connections to the relays etc.
It's not a hard job. Just takes a bit of time and patience.
| | |
|
|
|
|
| | |
| 2001 - 206 Hdi DTurbo with Partial Sport Pack
Remapped from 96 to 126HP
Next Upgrade(s): Uprated Clutch - FMIC - Next Remap | |
| | |
|
|
|
|
|
|
|
Posted: Sun Apr 01, 2012 6:51 am |
|
|
|
|
Joined: Feb 08, 2010
Posts: 7045
Trade Rating: +5
Location: In the garage
|
|
If all the wiring it past its best then I'd just remove it right back to the earth behind the bumpers and the fuse box.
| | |
|
|
|
|
| | |
| 2001 GTi 138, Bilstein Sprint dampers, H&R springs, 21mm Peugeot Sport torsion bars, 22mm rear ARB, Peugeot Sport Group A wishbones, 283mm discs, Goodridge stainless hoses, Maniflow 304 grade 4-2-1 2.5" manifold and system, 200 cell cat, Richard Longman head, 45mm Jenvey throttle bodies, 9.5mm TB spacers, 90mm air horns, Jenvey throttle linkage, Jenvey fuel rail, Aeromotive and Goodridge fuel fittings and braided hose, ITG sausage filter, Radtec custom radiator, Piper Ultimate Road cams, Piper vernier pulleys, Omex 600 ECU. Saxo electric PAS pump, Vibra Technics engine mounts. Samco coolant hoses, TTV steel flywheel, 4.76 final drive ratio, 307 CC 180 ratios. 2019 BMW 530i. 2017 Mercedes C300 convertible. | |
| | |
|
|
|
|
|
|
|
Posted: Sun Apr 01, 2012 7:13 am |
|
|
|
|
Joined: Aug 04, 2011
Posts: 1343
Trade Rating: 0
Location: Swindon
|
|
Dannskittles: if you haven't got one already you will need a wiring diagram to help with this. You may get lucky and find it just by disconnecting and reconnecting but the fan / air conditioning circuit is not a simple one on these and there are individual components and connectors that are used for the control of both the air conditioning and fan motor so I imagine the fault is related.
I think you will find the diagram on the www somewhere, I know I did but haven't kept it, but for example there are four fuses
F7, F21, F37 and F38 that all supply power to these systems. Start by checking those.
After that there are all the connections, the low speed fan relay and fan resistor.
However, again the previous advice, get a circuit diagram and a multi-meter. If you don't then good luck fault finding it could turn out to be time consuming.
| | |
|
|
|
|
| | |
| Morris 1000, Austin 1100, Escort Mk2, Fiat Mirafiori, Alfa 33, Alfa GT Junior, Alfasud, Alfetta GTV (2x), Alfa 164 3.0 V6, Alfa 164 2.0, Alfa 75 V6, Alfa 156 2.4 (diesel remapped 200bhp), Alfa 147 GTA (3.6 295bhp), Alfa 159 (diesel remapped 245bhp 300ft.lbs @ 2500rpm)
Why isn't my daughter an Alfaholic? | |
| | |
|
|
|
|
|
|
|
Posted: Sun Apr 01, 2012 7:15 am |
|
|
|
|
Joined: Feb 08, 2010
Posts: 7045
Trade Rating: +5
Location: In the garage
|
|
The fan wiring is really simple on these cars. No need for a wiring diagram.
| | |
|
|
|
|
| | |
| 2001 GTi 138, Bilstein Sprint dampers, H&R springs, 21mm Peugeot Sport torsion bars, 22mm rear ARB, Peugeot Sport Group A wishbones, 283mm discs, Goodridge stainless hoses, Maniflow 304 grade 4-2-1 2.5" manifold and system, 200 cell cat, Richard Longman head, 45mm Jenvey throttle bodies, 9.5mm TB spacers, 90mm air horns, Jenvey throttle linkage, Jenvey fuel rail, Aeromotive and Goodridge fuel fittings and braided hose, ITG sausage filter, Radtec custom radiator, Piper Ultimate Road cams, Piper vernier pulleys, Omex 600 ECU. Saxo electric PAS pump, Vibra Technics engine mounts. Samco coolant hoses, TTV steel flywheel, 4.76 final drive ratio, 307 CC 180 ratios. 2019 BMW 530i. 2017 Mercedes C300 convertible. | |
| | |
|
|
|
|
|
|
|
Posted: Sun Apr 01, 2012 7:25 am |
|
|
|
|
Joined: Apr 01, 2012
Posts: 14
Trade Rating: 0
Location: Walsall
|
|
Well taking it apart tomorrow morning, so hopefully will be sorted by tomorrow afternoon and will post updates and try and get a few pics might help people out abit. So will keep you updated.
| | |
|
|
|
|
| | |
| Why do we bother with French cars! I just keep buying them. | |
| | |
|
|
|
|
|
|
|
Posted: Sun Apr 01, 2012 7:52 am |
|
|
|
|
Joined: May 20, 2010
Posts: 365
Trade Rating: +5
Location: Newcastle
|
|
ill say 90% that its the fan relays.
i had the exact same problem, both relays wer coroded very badly which also caused a wire to snap.
2 new relays and some new wire and al sortd, cooling fan an a/c fan work perfectly.
i didnt have a front grill in at the time which made it very easy just keep your hands away from the fan 
| | |
|
|
|
|
|
|
|
|
|
|
Posted: Sun Apr 01, 2012 9:21 am |
|
|
|
|
Joined: Feb 07, 2010
Posts: 696
Trade Rating: 0
Location: Near Manchester
|
|
I had this too. Easy/cheap to fix.
| | |
|
|
|
|
| | |
| 206 GTI
Nimrods
SP Grille
Cargo Net!
Team: Old school member since May 2006 - 3k posts lost 
Leader Team: Tivoli GTI
Leader Team: Cargo Net
Snowboard & Bindings For Sale
www.goneboarding.co.uk...ified.aspx | |
| | |
|
|
|
|
|
|  |
| |
| |
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum
You cannot attach files in this forum
You can download files in this forum
|
|
|
| |
|
Membership:
Latest: 
New Today: 0
New Yesterday: 0
Overall: 17129
Online Now [129]:
Visitors: 128
Members: 0
Staff Online Now:
Page Views:
Forums Home
Forum FAQ
Search
