|
Author
|
Message |
|
|
 Posted: Sat Apr 14, 2012 2:27 am |
|
|
|
|
Joined: Feb 07, 2010
Posts: 2949
Trade Rating: +6
Location: Athens, Greece
|
 |
As title says.
Rattling noise (ball-bearing?) but my mech recons it's not the clutch release as that would make noise when pressing pedal.
It was also replaced along with the clutch plate/disk about a year ago (genuine pug).
So what is it exactly?
Cheers.
UPDATE - Page 2.
| |  |
|
|
 |
 | |  |
| 1.4i, 2001, 3-door, China Blue
Repair safely - Drive safely | |
 | |  |
Last edited by V9977 on Mon Jun 17, 2013 4:20 am; edited 2 times in total
|
|
|
|
|
|
|
Posted: Sat Apr 14, 2012 2:30 am |
|
|
|
|
Joined: Aug 19, 2011
Posts: 619
Trade Rating: +2
Location: Wiltshire
|
|
Mine did this for ages, and my gearbox went Monday.
| | |
|
|
|
|
| | |
| Project Low and Slow.. Going Euro for 2013. Keep your eyes peeled, big plans ahead..
See my project here. | |
| | |
|
|
|
|
|
|
|
Posted: Sat Apr 14, 2012 2:32 am |
|
|
|
|
Joined: Feb 07, 2010
Posts: 2949
Trade Rating: +6
Location: Athens, Greece
|
|
Nice.
| | |
|
|
|
|
| | |
| 1.4i, 2001, 3-door, China Blue
Repair safely - Drive safely | |
| | |
|
|
|
|
|
|
|
Posted: Sat Apr 14, 2012 2:32 am |
|
|
|
|
Joined: Apr 30, 2011
Posts: 1676
Trade Rating: +46
Location: durham
|
|
possable thrust bearing?
| | |
|
|
|
|
|
WARNING: This User Has Had Bad Trade Feedback In The Past
|
|
|
|
|
|
|
Posted: Sat Apr 14, 2012 2:34 am |
|
|
|
|
Joined: Feb 07, 2010
Posts: 2949
Trade Rating: +6
Location: Athens, Greece
|
|
OK, where exactly is that?
Is that on the crank-shaft?
| | |
|
|
|
|
| | |
| 1.4i, 2001, 3-door, China Blue
Repair safely - Drive safely | |
| | |
|
|
|
|
|
|
|
Posted: Sat Apr 14, 2012 2:50 am |
|
|
|
|
Joined: Aug 21, 2011
Posts: 40
Trade Rating: 0
Location: Birmingham
|
|
same as the release bearing, mine does it too. and used to to it on my 106 until i couldn't bare it anymore so had the clutch and release bearing changed.
| | |
|
|
|
|
|
|
|
|
|
|
Posted: Sat Apr 14, 2012 3:05 am |
|
|
|
|
Joined: Feb 07, 2010
Posts: 2949
Trade Rating: +6
Location: Athens, Greece
|
|
Damn.
Not pleased if it's this as it was fitted new and genuine about a year ago.
| | |
|
|
|
|
| | |
| 1.4i, 2001, 3-door, China Blue
Repair safely - Drive safely | |
| | |
|
|
|
|
|
|
|
Posted: Sat Apr 14, 2012 3:05 am |
|
|
|
|
Joined: Aug 01, 2011
Posts: 390
Trade Rating: 0
Location: Bath UK
|
|
It's logical to expect the clutch release bearing to make most of the noise when depressing it as that's when it's under load but it can rattle in its cage when fully up and can squeal when worn and under very light load when pedal is fully up
Sometimes if you pull the clutch lever on the gearbox even fuller back from the rest position and the noise stops then you know what it is for certain
| | |
|
|
|
|
|
|
|
|
|
|
Posted: Sat Apr 14, 2012 3:09 am |
|
|
|
|
Joined: Feb 07, 2010
Posts: 2949
Trade Rating: +6
Location: Athens, Greece
|
|
So are you saying it could be the release bearing even though it stops when pedal is pressed?
Not pleased if it's this as it was fitted new and genuine (Valeo) about a year ago.
| | |
|
|
|
|
| | |
| 1.4i, 2001, 3-door, China Blue
Repair safely - Drive safely | |
| | |
|
|
|
|
|
|
|
Posted: Sat Apr 14, 2012 3:17 am |
|
|
|
|
Joined: Aug 01, 2011
Posts: 390
Trade Rating: 0
Location: Bath UK
|
|
Yes, especially a loose rattling in its cage or a squealing when cold which lessens as it warms up
A rattling or chattering is just that though and they have been known to stop doing it on their own as the release bearing is just catching at the rest position. Try pulling the lever back a bit further and see if it stops then you'll know and you can show your mechanic
| | |
|
|
|
|
|
|
|
|
|
|
Posted: Sat Apr 14, 2012 4:27 am |
|
|
|
|
Joined: Feb 07, 2010
Posts: 2949
Trade Rating: +6
Location: Athens, Greece
|
|
How can I pull the lever back if the clutch cable is preventing it?
Also, it only stops when fully depressing pedal and only does it 3 out of 5 times at varying level of noise.
Cheers for replies all.
| | |
|
|
|
|
| | |
| 1.4i, 2001, 3-door, China Blue
Repair safely - Drive safely | |
| | |
|
|
|
|
|
|
|
Posted: Sat Apr 14, 2012 5:04 am |
|
|
|
|
Joined: Aug 01, 2011
Posts: 390
Trade Rating: 0
Location: Bath UK
|
|
How can I pull the lever back if the clutch cable is preventing it?
The cable should never be pulling so tight that there is no slack at all at the lever when pedal is fully up
206 clutch cable
| | |
|
|
|
|
|
|
|
|
|
|
Posted: Sat Apr 14, 2012 5:10 am |
|
|
|
|
Joined: Feb 07, 2010
Posts: 2949
Trade Rating: +6
Location: Athens, Greece
|
|
OK. 'Will check. Thanks.
| | |
|
|
|
|
| | |
| 1.4i, 2001, 3-door, China Blue
Repair safely - Drive safely | |
| | |
|
|
|
|
|
|
|
Posted: Sat Apr 14, 2012 6:23 am |
|
|
|
|
Joined: Mar 29, 2010
Posts: 153
Trade Rating: 0
Location: London
|
|
Clutch cable are self adjusting due to the design of it (self adjusting mechanism) U better dun touch it, once u remove it, will be pain in the butt to put it right again.
I am sure will be the bearing for the clutch cause i have similar problem and it gone when i replace with complete clutch kit.
After u warm up the car or drive for some distance will it get better?
| | |
|
|
|
|
|
|
|
|
|
|
Posted: Sat Apr 14, 2012 6:32 am |
|
|
|
|
Joined: Aug 01, 2011
Posts: 390
Trade Rating: 0
Location: Bath UK
|
|
Now don't make the guy paranoid 
No one said anything about removing cables, just checking for the 5mm or so of slack which the self adjusting cable should automatically put into the system. It's how you check that the cable's been installed and adjusting correctly
| | |
|
|
|
|
|
|
|
|
Membership:
Latest: 
New Today: 0
New Yesterday: 0
Overall: 17130
Online Now [66]:
Visitors: 65
Members: 0
Staff Online Now:
Page Views:
General
Forums Home
Forum FAQ
Search
york 16,3
