Author
|
Message |
|
Posted: Sat Jun 16, 2012 3:17 pm |
|
|
|
Joined: Jun 16, 2012 Posts: 7
Trade Rating: 0
Location: Sussex
|
|
Hello all,
I have a problem with a 206 1.4 Quicksliver. It recently went in for a new clutch. On return it has difficulty engaging gears. It doesn't crunch, but it isn't easy to get the lever in to the correct position and engage the gear. It seems to be fine when stationary or at a low speed. for example, changing down from 3rd to 2nd. It doesn't want to go in. If you hold the gear lever where 2nd should be and slow the car right down, it will go in to gear when the speed is low enough.
The garage who changed the clutch say it is the linkages. These were working fine before we took it in though. I understand they had problems disconnecting the linkages.
I was previously thinking that this is the garages fault and that they should put it right, but they are not going to do so after speaking with them. I suppose things like this don't always go smoothly and I did not want to be doing the clutch change myself. They did offer to replace the linkages for the cost of the parts (no labour). Sound fair?
Anyway... I'm not convinced it is actually the linkages due to it only being an issue when moving. If it was the linkages, surely it would be difficult to engage gears even when stationary? If this is the case, the garage has buggered something else up.
The biting point doesn't seem too low so I think the clutch is fully disengaged when your foot is to the floor.
Any thoughts?
Cheers,
Paul
| | |
|
|
|
|
|
|
|
Posted: Sat Jun 16, 2012 3:27 pm |
|
|
|
Joined: Feb 08, 2010 Posts: 10151
Trade Rating: +12
|
|
i think could be gear oil.
ask them what oil do they put in
| | |
|
|
|
|
|
|
|
Posted: Sat Jun 16, 2012 4:25 pm |
|
|
|
Joined: Feb 07, 2010 Posts: 2720
Trade Rating: +6
Location: UK
|
|
Seabook wrote: |
i think could be gear oil.
ask them what oil do they put in |
+1
| | |
|
|
|
|
|
|
|
Posted: Sat Jun 16, 2012 5:08 pm |
|
|
|
Joined: Jun 16, 2012 Posts: 7
Trade Rating: 0
Location: Sussex
|
|
Interesting... What oil should be in there?
I did notice it seemed to be too full so was wondering if that could cause it. I was replacing the wishbones today and removed the driveshaft, forgetting it is fed from the gearbox, so drained it out in to a container. Refilling via the plug it wouldn't take all of the oil that I had removed.
The only reference I have found so far is from Halfords, specifying 75w/90 GL-5 but I have no idea what the garage would have (over)filled it with.
Can the wrong oil cause these problems? Too viscous?
Cheers,
Paul
| | |
|
|
|
|
|
|
|
Posted: Sun Jun 17, 2012 1:42 am |
|
|
|
Joined: Feb 07, 2010 Posts: 2720
Trade Rating: +6
Location: UK
|
|
75/80 I think it is, I'll check the manual. If they filled it from the correct filling hole, it's impossible to overfilled, it would leak out as they put it in. Your be surprised the difference the wrong oil makes. It takes about 1.9 litres on my gti.
| | |
|
|
|
|
|
|
|
Posted: Sun Jun 17, 2012 2:55 am |
|
|
|
Joined: Jun 16, 2012 Posts: 7
Trade Rating: 0
Location: Sussex
|
|
Cheers Steve206, that'd be good.
I found a guide on refilling the gearbox online (http://206gti.net/gear-oil/). Fairly obvious filler hole under the passenger side wheel arch, behind the plastic liner.
I couldn't get all of the oil back in there so i'm not sure where they would have filled it from.
It definitely had a synthetic gearbox oil smell to it as I was wearing some in my hair!
| | |
|
|
|
Last edited by poltn6 on Sun Jun 17, 2012 5:45 am; edited 1 time in total
|
|
|
|
|
Posted: Sun Jun 17, 2012 2:56 am |
|
|
|
Joined: Feb 07, 2010 Posts: 2949
Trade Rating: +6
Location: Athens, Greece
|
|
"Total BV 75W80" semi-synthetic only.
| | |
|
|
|
| | |
| 1.4i, 2001, 3-door, China Blue
Repair safely - Drive safely | |
| | |
|
|
|
|
|
Posted: Sun Jun 17, 2012 5:45 am |
|
|
|
Joined: Jun 16, 2012 Posts: 7
Trade Rating: 0
Location: Sussex
|
|
V9977 wrote: |
"Total BV 75W80" semi-synthetic only. |
Cheers for that. I'll try and find out what the garage used.
| | |
|
|
|
|
|
|
|
Posted: Sun Jun 17, 2012 6:32 am |
|
|
|
Joined: Nov 27, 2010 Posts: 11520
Trade Rating: +10
Location: What's it to you? ? ?
|
|
Synthetic gear oil + MA gearbox = problems
| | |
|
|
|
| | |
| Toyota C-HR GR Sport 2.0 Hybrid with JBL & Alcantara packs. | |
| | |
|
|
|
|
|
Posted: Tue Jun 19, 2012 6:56 am |
|
|
|
Joined: Jun 16, 2012 Posts: 7
Trade Rating: 0
Location: Sussex
|
|
Well, they say they put in 75/80 as per the manufacturers spec, but they had to go and check for me.
Do any of you think this sounds like a gear linkage problem?
It only happens when revs are up. Low speed / revs it seems fine to engage gears. I suppose the gearbox would move a bit when in use but I would have expected a dodgy linkage to feel the same when stationary / slow moving.
Cheers,
Paul
| | |
|
|
|
|
|
|
|
Posted: Tue Jun 19, 2012 10:49 am |
|
|
|
Joined: Aug 01, 2011 Posts: 390
Trade Rating: 0
Location: Bath UK
|
|
It doesn't crunch, but it isn't easy to get the lever in to the correct position and engage the gear. It seems to be fine when stationary or at a low speed. for example, changing down from 3rd to 2nd. It doesn't want to go in. If you hold the gear lever where 2nd should be and slow the car right down, it will go in to gear when the speed is low enough.
That really sounds like the clutch is dragging ie not fully disengaged.
Is this a cable or hydraulic operated clutch?
| | |
|
|
|
|
|
|
|
Posted: Fri Jun 22, 2012 6:55 am |
|
|
|
Joined: Jun 16, 2012 Posts: 7
Trade Rating: 0
Location: Sussex
|
|
Hmmm, it does. I don't know actually. I assumed it was cable. It's my sisters car so I can't check right now. Do certain years / models use cable / hydraulic?
Either way, can it be adjusted?
I'm sure the garage are just talking crap. I would like them to put it right but all they want to do is replace the linkages.
Thanks,
Paul
| | |
|
|
|
|
|
|
|
Posted: Fri Jun 22, 2012 6:57 am |
|
|
|
Joined: Nov 27, 2010 Posts: 11520
Trade Rating: +10
Location: What's it to you? ? ?
|
|
It will be a self adjusting clutch cable on a 1.4 petrol Quicksilver.
| | |
|
|
|
| | |
| Toyota C-HR GR Sport 2.0 Hybrid with JBL & Alcantara packs. | |
| | |
|
|
|
|
|
Posted: Fri Jun 22, 2012 8:34 am |
|
|
|
Joined: Aug 04, 2011 Posts: 1343
Trade Rating: 0
Location: Swindon
|
|
There is an automatic adjuster built into the cable and they don't always work so you could try the forced clutch adjustment trick.
Press the clutch pedal to the floor.
Slip your foot sideways off the clutch pedal and let if "fly" back.
Be careful it doesn't hit you in the leg as it will shoot up with some force. Not enough to really hurt but uncomfortable!
This sometimes makes a sticking self adjusting mechanism work.
It may take two or three attempts or it may not make any difference.
If this doesn't work take it back and show them what is happening - it is not right and they should fix it.
| | |
|
|
|
| | |
| Morris 1000, Austin 1100, Escort Mk2, Fiat Mirafiori, Alfa 33, Alfa GT Junior, Alfasud, Alfetta GTV (2x), Alfa 164 3.0 V6, Alfa 164 2.0, Alfa 75 V6, Alfa 156 2.4 (diesel remapped 200bhp), Alfa 147 GTA (3.6 295bhp), Alfa 159 (diesel remapped 245bhp 300ft.lbs @ 2500rpm)
Why isn't my daughter an Alfaholic? | |
| | |
|
|
|
|
|
Posted: Fri Jun 22, 2012 8:40 am |
|
|
|
Joined: Aug 04, 2011 Posts: 1343
Trade Rating: 0
Location: Swindon
|
|
Just a thought - if the old clutch was worn then the automatic cable adjuster will have slowly taken up that wear by automatically adusting itself. (I know what I mean but does this make sense?)
How do you reset the adjuster to take into account the fact that you now have a new, unworn clutch? Do you have to fit a new cable or can the adjuster on the existing cable be manually reset?
| | |
|
|
|
| | |
| Morris 1000, Austin 1100, Escort Mk2, Fiat Mirafiori, Alfa 33, Alfa GT Junior, Alfasud, Alfetta GTV (2x), Alfa 164 3.0 V6, Alfa 164 2.0, Alfa 75 V6, Alfa 156 2.4 (diesel remapped 200bhp), Alfa 147 GTA (3.6 295bhp), Alfa 159 (diesel remapped 245bhp 300ft.lbs @ 2500rpm)
Why isn't my daughter an Alfaholic? | |
| | |
|
|
|
|
|