|
Author
|
Message |
|
|
 Posted: Fri Oct 14, 2011 11:16 am |
|
|
|
|
Joined: Sep 03, 2010
Posts: 979
Trade Rating: +6
Location: Biggleswade
|
 |
hi there, as i will be changing my gearbox mount tomorrow i thought i would by the left mount at the same time and do that, but im abit nervious about doing it as it looks like the ecu needs to be removed, if anyone has done this before could you give me any tips etc on remving the mount,
Thanks Dan
| |  |
|
|
 |
|
|
|
|
|
|
Posted: Fri Oct 14, 2011 1:26 pm |
|
|
|
|
Joined: Feb 08, 2010
Posts: 960
Trade Rating: +11
Location: Hertfordshire
|
|
gearbox mount requires the battery tray to be removed iirc but thats about it.
ECU is the other side, forward of the upper engine mount.
| | |
|
|
|
|
|
|
|
|
|
|
Posted: Fri Oct 14, 2011 1:48 pm |
|
|
|
|
Joined: Sep 03, 2010
Posts: 979
Trade Rating: +6
Location: Biggleswade
|
|
Thanks so basically all I do is undo that nut holding the ecu on lift the ecu out the way, do i not need to unplug any of the connectors
| | |
|
|
|
|
|
|
|
|
|
|
Posted: Fri Oct 14, 2011 3:22 pm |
|
|
|
|
Joined: Feb 08, 2010
Posts: 7045
Trade Rating: +5
Location: In the garage
|
|
That ECU looks like it's been off before. Should be easy to remove it then.
| | |
|
|
|
|
 | |  |
| 2001 GTi 138, Bilstein Sprint dampers, H&R springs, 21mm Peugeot Sport torsion bars, 22mm rear ARB, Peugeot Sport Group A wishbones, 283mm discs, Goodridge stainless hoses, Maniflow 304 grade 4-2-1 2.5" manifold and system, 200 cell cat, Richard Longman head, 45mm Jenvey throttle bodies, 9.5mm TB spacers, 90mm air horns, Jenvey throttle linkage, Jenvey fuel rail, Aeromotive and Goodridge fuel fittings and braided hose, ITG sausage filter, Radtec custom radiator, Piper Ultimate Road cams, Piper vernier pulleys, Omex 600 ECU. Saxo electric PAS pump, Vibra Technics engine mounts. Samco coolant hoses, TTV steel flywheel, 4.76 final drive ratio, 307 CC 180 ratios. 2019 BMW 530i. 2017 Mercedes C300 convertible. | |
 | |  |
|
|
|
|
|
|
|
Posted: Fri Oct 14, 2011 3:26 pm |
|
|
|
|
Joined: Sep 03, 2010
Posts: 979
Trade Rating: +6
Location: Biggleswade
|
|
ah thanks edward, so i dont have a stupid anti tamper nut then, should it lift up and out the way after that 1 nut is removed, enough for me to get a chain around mount, or will unplugging the connectors and removing the ecu out the car be better,
Thanks
| | |
|
|
|
|
|
|
|
|
|
|
Posted: Fri Oct 14, 2011 4:21 pm |
|
|
|
|
Joined: Oct 14, 2011
Posts: 117
Trade Rating: +9
Location: Llantrisant
|
|
Should give you plenty of room after you undo that nut without needing to unplug the ecu  Done a few!
| | |
|
|
|
|
|
WARNING: This User Has Had Bad Trade Feedback In The Past
|
|
|
|
|
|
|
Posted: Fri Oct 14, 2011 4:27 pm |
|
|
|
|
Joined: Sep 03, 2010
Posts: 979
Trade Rating: +6
Location: Biggleswade
|
|
sorry if i sound dumb, but is that 1 nut the only thing holding the ecu inplace 
| | |
|
|
|
|
|
|
|
|
|
|
Posted: Fri Oct 14, 2011 4:34 pm |
|
|
|
|
Joined: Oct 14, 2011
Posts: 117
Trade Rating: +9
Location: Llantrisant
|
|
yep, that one nut and it should pull out of the way!
| | |
|
|
|
|
|
WARNING: This User Has Had Bad Trade Feedback In The Past
|
|
|
|
|
|
|
Posted: Fri Oct 14, 2011 4:35 pm |
|
|
|
|
Joined: Sep 03, 2010
Posts: 979
Trade Rating: +6
Location: Biggleswade
|
|
wow, thought it would be on better than that might have to fit a nyloc on refitting
Thanks for your advise
| | |
|
|
|
|
|
|
|
|
|
|
Posted: Fri Oct 14, 2011 4:41 pm |
|
|
|
|
Joined: Oct 14, 2011
Posts: 117
Trade Rating: +9
Location: Llantrisant
|
|
No problem, much easier without the anti tamper nut that you don't seem to have!
| | |
|
|
|
|
|
WARNING: This User Has Had Bad Trade Feedback In The Past
|
|
|
|
|
|
|
Posted: Fri Oct 14, 2011 4:44 pm |
|
|
|
|
Joined: Sep 03, 2010
Posts: 979
Trade Rating: +6
Location: Biggleswade
|
|
aha  no chance that anoying nut wont be under that black thing which looks like a cover not sure, i feel so stupid but never had an ecu off a 206 so dont know what 1 looks like
| | |
|
|
|
|
|
|
|
|
|
|
Posted: Sat Oct 15, 2011 1:56 am |
|
|
|
|
Joined: Feb 08, 2010
Posts: 7045
Trade Rating: +5
Location: In the garage
|
|
The ECU and bracket get removed, the ECU might be held onto the bracket with a security nut/bolt but as you remove ECU and bracket together it's not a problem.
| | |
|
|
|
|
| | |
| 2001 GTi 138, Bilstein Sprint dampers, H&R springs, 21mm Peugeot Sport torsion bars, 22mm rear ARB, Peugeot Sport Group A wishbones, 283mm discs, Goodridge stainless hoses, Maniflow 304 grade 4-2-1 2.5" manifold and system, 200 cell cat, Richard Longman head, 45mm Jenvey throttle bodies, 9.5mm TB spacers, 90mm air horns, Jenvey throttle linkage, Jenvey fuel rail, Aeromotive and Goodridge fuel fittings and braided hose, ITG sausage filter, Radtec custom radiator, Piper Ultimate Road cams, Piper vernier pulleys, Omex 600 ECU. Saxo electric PAS pump, Vibra Technics engine mounts. Samco coolant hoses, TTV steel flywheel, 4.76 final drive ratio, 307 CC 180 ratios. 2019 BMW 530i. 2017 Mercedes C300 convertible. | |
| | |
|
|
|
|
|
Membership:
Latest: 
New Today: 0
New Yesterday: 0
Overall: 17128
Online Now [75]:
Visitors: 74
Members: 0
Staff Online Now:
Page Views:
General
Forums Home
Forum FAQ
Search
